ITT Flygt 3102 Скачать руководство пользователя страница 15

Страница: 15 / 72

• The voltage drop in long cables must be taken into account. The drive unit’s rated voltage is the

voltage measured at the terminal board in the upper part of the pump.

• The screened cable must be used according to the European CE requirements if a Variable Frequency

Drive (VFD) is used. For more information, contact your ITT representative (VFD-supplier).

Earthing (Grounding)

Electrical Hazard:

• You must earth (ground) all electrical equipment. This applies to the pump equipment, the driver, and

any monitoring equipment. Test the earth (ground) lead to verify that it is connected correctly.

• If the motor cable is jerked loose by mistake, the earth (ground) conductor should be the last

conductor to come loose from its terminal. Make sure that the earth (ground) conductor is longer
than the phase conductors. This applies to both ends of the motor cable.

• Risk of electrical shock or burn. You must connect an additional earth- (ground-) fault protection

device to the earthed (grounded) connectors if persons are likely to come into physical contact with
the pump or pumped liquids.

Connect the motor cable to the pump

CAUTION:
Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep the end of the motor
cable above the liquid level.

Entrance cover

O-ring

For information about the cable entry, see the Parts list.
1. Remove the entrance cover and the O-ring from the stator housing.

This provide access to the terminal board/closed end splices.

Installation (Continued)

Flygt 3102 Service and Repair Instructions

Содержание Flygt 3102









































































Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды

ITT Flygt 3102, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание Flygt 3102

Отзывы:

Похожие инструкции для Flygt 3102

Бренды по названию

Популярные бренды