background image

1 Introduction and Safety

1.1 Safety message levels

Definitions

Safety message level

Indication

DANGER:

 

A hazardous situation which, if not avoided, will result in death or
serious injury

WARNING:

 

A hazardous situation which, if not avoided, could result in death
or serious injury

CAUTION:

 

A hazardous situation which, if not avoided, could result in minor
or moderate injury

ELECTRICAL
HAZARD:

 

The possibility of electrical risks if instructions are not followed in a
proper manner

NOTICE:

 

A potential situation which, if not avoided, could result in an
undesirable result or state

A practice not related to personal injury

1.2 User health and safety

General precautions

This product is designed and manufactured using good workmanship and materials, and meets all appli-
cable industry standards. This product should be used only as recommended by ITT.

 

WARNING:

Misapplication of the valve can result in injury or property damage. Select valves and
valve components of the proper materials and make sure that they are consistent with
your specific performance requirements. Incorrect application of this product includes but
is not limited to:

Exceeding the pressure or temperature rating

Failing to maintain this product according to the recommendations

Using this product to contain or control media that is incompatible with the materials
of construction

Proper containment or protection from hazardous media must be provided by the
end user to protect employees and the environment from valve discharge.

If the product exhibits any indication of leakage, do not operate. Isolate the product and
either repair it or replace it as outlined within this manual.

 

1 Introduction and Safety

2

Handwheel Operated Valves (903, 913, 963) Installation, Operation, and Maintenance Manual

Содержание Engineered Valves 903
























Отзывы: