ITT Industries Neo-Dyn 801P5 Скачать руководство пользователя страница 27

Страница: 27 / 45

Page 23

801P5 Smart Switch

NOTE

Pressure Calibration

(PCAL)

You can do a field pressure calibration using this function.
After

PCAL

is displayed, use the

[SELECT]

key to enter the

submenu.

LO-P

will be displayed for one second, and then

the switch’s interpretation of the actual pressure will be
displayed. Apply 0.0 psig to the unit. Use the

[UP/DOWN

ARROW]

keys to adjust the pressure display to zero psig.

Press the

[STORE]

key. The display will show

HI-P

for one

second, followed by the switch’s interpretation of the actual
pressure applied. Apply Full- Scale pressure to the unit. Use
the

[UP/DOWN ARROW]

keys to set the display equal to

Full- Scale pressure. Press the

[STORE]

key to return to the

main menu.

A pressure source is required for this operation. In addition,
calibration equipment used must have an accuracy of at least
± 0.02% F.S.O. of the switch being calibrated.

If re-calibration results in zero or Full-Scale readings that have
shifted by 4% F.S.O. or more from the factory calibration, an
error code of

EROR

will be displayed.

Reset (rSET)

This command resets the Smart-Switch

to factory default

settings. After

rSET

appears, press

[SELECT], [STORE]

[RUN]

and

[SELECT]

to reset the unit to factory defaults.

These are as follows:

r-Hi

returns to factory F.S.O.

r-Lo

is set to zero

Spli

is set to 60% of the full range.

SPld

is set to 40% of the full range.

SP2i

is set to 70% of the full range.

SP2d

is set to 30% of the full range.

Switch delay is set to 0 mSec.

Display update time is set to 0.5 seconds.

All manuals and user guides at all-guides.com

Содержание Neo-Dyn 801P5














































Результаты поиска

Содержание Neo-Dyn 801P5

Отзывы:

Похожие инструкции для Neo-Dyn 801P5

Бренды по названию

Популярные бренды

ITT Industries Neo-Dyn 801P5, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Neo-Dyn 801P5

Отзывы:

Похожие инструкции для Neo-Dyn 801P5

Бренды по названию

Популярные бренды