NOTE: If your net does not fit the first time,
you may be fitting it to the goal frame upside
down i.e. that is to say the net from the crossbar to
the floor (a) is longer than the length of the net to
the bottom of the upright.(b)
STEP BY STEP NET FITTING
ANCHORING YOUR GOAL
STEP 1
Open net and check the lengths of a and b
correspond with the diagram below.
STEP 3
Attach the corners first, where the upright
posts meets the crossbar as shown.
Then attach the net to the post using
the Arrow head net
fixings on crossbar
and uprights.
STEP 4
Using the large net ties tie the
net to the ground side frame
back ground frame.
STEP 5
Using the small net ties
attach the net down the
back of the sloping
back net supports as
shown to the posts
as shown.
STEP 6
NET CORD - ROOF TO THE NET
To help define the roof of the net Tie the
cord to one side and pull the net chord
tight and wrap neatly down and around
the stanchion section.
If you are regularly attaching or detaching
the net then apply coloured tape to the
roof corners of net to help identify the
roof area.
STEP 2
With the net the correct way round
lift the net onto the goalpost frame.
This is easier with two people.
a
b
a
b
NET
CHORD
OPTIONAL - STANCHION TIES
9
10
GROUND
PEG REMOVAL
D
E
USE THE HOOK ON THE END
OF THE RED GROUND PEG
TO REMOVE PEGS FROM THE GROUND OR USE
A CLAW HAMMER FOR PEGS THAT ARE
DIFFICULT TO REMOVE.
WARNING: Check the position of any underground services before using
the ground anchors and pegs. We take no responsibility for any damage
or injury caused in this manner.
HARD SURFACES: to prevent damage to goal or it's components, loosen
soil with a steel pole and moisten with some water before inserting the
ground anchors. Do not use the goal in sub zero temperatures.
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A
LEVEL PLAYING SURFACE. PLACE THE MULTI-SURFACE ANCHOR OVER
EACH SIDE OF THE GROUND FRAME (POSITIONS SHOWN) HAMMER THE
PEGS THROUGH THE HOLES (DO NOT USE METAL HAMMERS USE
RUBBER MALLETS) ON THE ANCHOR DOWN UNDER THE FRAME INTO
THE GRASS ADDITIONAL ANCHORS OR LARGER PEGS CAN BE
PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE ANCHORS
CAN BE USED FOR HARD SURFACES SUCH AS TARMAC WITH
OPTIONAL BOLTS. ON HOT/SUNNY DAYS TARMACADAM SOFTENS AND
THEREFORE TO ANCHOR
YOUR GOAL PROPERLY YOU MUST:-
1 DIG HOLES IN YOUR TARMAC FILL HOLES WITH CONCRETE
2 DRILL TWO 14MM HOLES 12CM APART AND 70MM DEPTH.
3 POSITION GOAL AND ANCHOR, INSERT AND TIGHTEN BOLT.
FOR OTHER SURFACES SUCH AS WOODEN SPORTS HALL FLOORS
WOOD SCREWS (INSTEAD OF BOLTS) OR COUNTER BALANCE
WEIGHTS CAN ALSO BE USED (SUPPLIED SEPARATELY).
INSERT MULTI-SURFACE
ANCHOR PEGS FULLY
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
LONGER GROUND PEGS ARE AVAILABLE SEPARATELY.
200mm
STANDARD
300mm
SOFTER GROUND
Longer pegs are to be used on sandy or
Soft ground earth. A risk assessment of soil
conditions suitability should be carried out when
anchors are to be used.
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD,
ALL RIGHTS RESERVED A REGISTERED DESIGN
SPARE PARTS
TEL:
0114 24 34 200
For help contact
www.footiegoals.com
