background image

2

Symbols, safety

Important, safety information, recommendation

Maintenance

Contents

General safety information

The details and information in the installation guide are provided for the purposes of 

describing the product and its assembly only. The information does not discharge 

the user from the obligation to carry out his own assessments and checks. It is 

important to bear in mind that our products are subject to a natural process of wear 

and ageing. These notes contain important information that will enable you to use 

the product safely and appropriately. When sold, rented out or otherwise passed on 

to another party, this product must be handed over with the installation guide.
When installing, operating and maintaining Linear Unit KRF 8 80x40 ZR, it is 

important to ensure that all moving elements are secured so that they cannot 

be switched on and moved unintentionally. Rotating and moving parts can 

cause serious injury! You must therefore read and follow the safety instructions 

set out below.

 

ƒ

All work on and with Linear Unit KRF 8 80x40 ZR must be performed with 

“safety first” in mind.

 

ƒ

Always switch off the drive assembly before you start working on Linear Unit 

KRF 8 80x40 ZR

 

ƒ

Ensure the drive unit cannot be switched on unintentionally, e.g. by affixing warn-

ing notices at the activation point or by removing the fuse from the power supply.

 

ƒ

Do not place your hand within the operating range of moving parts in Linear 

Unit KRF 8 80x40 ZR when the unit is still switched on.

 

ƒ

Fit guards and covers so that the moving parts of Linear Unit KRF 8 80x40 ZR 

cannot be touched unintentionally.

 

ƒ

Observe the regulations pertaining to accident prevention and environmental 

protection that apply in the country and place of work where the product is 

being used.

 

ƒ

Use only item products that are in perfect working order.

 

ƒ

Failure to use original spare parts will invalidate the product warranty!

 

ƒ

Check the product for obvious defects.

 

ƒ

Use the product only within the performance range described in the technical 

data.

 

ƒ

Ensure that all the safety equipment associated with the product is present, 

properly installed and in full working order.

 

ƒ

Do not alter the position of safety equipment, circumvent it or render it  

ineffective.

Accessories 

9

Correct use

3

General safety information

2

Improper use

3

Installation

5

Maintenance

11

Operating parameters

4

Symbols, safety

2

Содержание 0.0.641.21













Отзывы: