ITech IT-M3300 Series Скачать руководство пользователя

Страница: 82 / 110

Trace Commands

Returns

0|1

TRACe:DATA?

This command reads all values saved in the cache.

Note

Before sending the query command TRACe:DATA?, the command TRIGger[:IMMediate]

must be sent to the instrument to trigger the instrument into data storage status. And the

argument of the command TRACe:FEED:CONTrol <NEXT|ALWays|NEVer> must be set

to NEXT or ALWays, otherwise the system will prompt an error.

Syntax

TRACe:DATA?

Arguments

None

Example

TRACe:DATA?

Returns

<NRf>,<NRf>,<NRf>.....

TRACe:FILTer[:STATe]

This command enables or disables the filter.

Syntax

TRACe:FILTer[:STATe]

Arguments

<0|1|OFF|ON>

Default value

OFF

Example

TRAC:FILT 0

Returns

0|1

Содержание IT-M3300 Series















































































































Результаты поиска

Содержание IT-M3300 Series

Отзывы:

Похожие инструкции для IT-M3300 Series

Бренды по названию

Популярные бренды

ITech IT-M3300 Series, Руководство по программированию

Результаты поиска

Содержание IT-M3300 Series

Отзывы:

Похожие инструкции для IT-M3300 Series

Бренды по названию

Популярные бренды