iSTEK K100-TB Скачать руководство пользователя

Страница: 13 / 15

Water Quality Measuring Instrument

CHAPTER 3.

Trouble and Solution

Error

Reason

Solution

Low battery

Change for new battery.

Power-

intensive

Battery’s bad quality

Change battery

Too many functions were used

Adjust to the suitable back light,
auto power off time, and the
voice according to customer
need.

Out of range

Turbidity is too high

Dilute the water sample

Please close the shielded cap

Cap was open.

Close the cap

Calibration failed

-Standard solution is not the
same as the set concentration.
-The deviation between
standard solution and
theoretical value is high.
-Sample cell is dirty or with
bubbles.
-Sample is not fully mixed.

Check the reasons and remove it.

Wrong password

Input correct password

The result is not accurate

Don’t read manual carefully

Read manual carefully.

Inappropriate sample

The sample must be uniform,
representative and sample should
be fully mixed or shake.

Fingerprints or water marks on
Wall of sample cell

Clean the cell with wiper

Testing time is too long or short

The sample need shake
before

[p1]

testing, and make

sure there are no bubbles, then
test the sample quickly.

Not boot

- Low battery.
- The backlight is too dark.
- Device was turned off without

operation over the set time

- Device error

- Change new battery
- Setting the backlight
- Press any key to boot
- Return to seller for repair

3. Trouble and solution

Содержание K100-TB
















Результаты поиска

Содержание K100-TB

Отзывы:

Похожие инструкции для K100-TB

Бренды по названию

Популярные бренды

iSTEK K100-TB, Инструкция по эксплуатации

Результаты поиска

Содержание K100-TB

Отзывы:

Похожие инструкции для K100-TB

Бренды по названию

Популярные бренды