manualshive.com logo in svg

IST 18.BF200D, Руководство пользователя

Поделиться
Скачать
IST 18.BF200D Скачать руководство пользователя страница 52

18-52

The primer bulb must be positioned so that the 

outlet end is higher or can be positioned higher 

than the inlet end. The arrow on the primer bulb 
must point upward toward the engine.

ENGINE SIDE

Fuel line clamp pliers (A) allow you to effectively 
remove and install the Honda fuel line clamps. 
Available from the Parts Division through normal 
ordering procedures. 
The OETIKER clamp pincer pliers (B) are 
available through the Marine Tool and Equipment 
program by calling (888) 424-6857.  

If you are unable to properly crimp the band type 
clamp provided, use a quality 

lined

 stainless steel 

fuel hose clamp.

NOTICE

Do not tie the cables together within 300 mm 
(11.8 in) of the under-case grommet A. This will 
prevent stress flexing near the grommet, which 
could cause intermittent power.

BOAT SIDE

The fuel hose is 7.3 mm (5/16 in) and the male 
hose barb is stepped to 12 mm (0.4725 in). The 
priming bulb hose barbs are 7.3 mm (5/16 in). 
Make sure the fuel hose is not pinched or crushed 
as it routes to the boat fuel supply. This could 
cause an engine malfunction.

FUEL HOSE CLAMP

If the outboard motor fuel hose is going to be 
connected directly into the boat fuel tank supply 
hose, secure this hose by using a fuel hose clamp 
type as listed above. Secure the hose joint so that 
it does not bounce and become damaged on a 
hard surface.

Item

Description

Part Number

Use

A

Fuel line clamp pliers

07APF-ZV4A100

For use on band 
clamp

B

OETIKER clamp 
pincer pliers

MTP120024

For use on 3/8 in 
hose clip

A

B

BAND CLAMP
P/N 17704-ZV4-010

3/8 in HOSE CLIP
P/N 17800-ZY3-010AH

PRIMER 
BULB

ARROW

300 mm (11.8 in)

During operation, check for any fuel or air leaks 
and repair immediately. If these connections draw 
air, the engine fuel pump will malfunction.

FUEL HOSE CONNECTION

NOTICE

Do not use unlined, worm-type fuel hose clamps. 
They may cause leaks by damaging the outside of 

 

the fuel hose.

Содержание 18.BF200D

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды