background image

 

 

                   

                  

 

                 PLACEMENT 

 

The  SA115  is  designed  to  sit directly  on  the floor or  stage.    Do  not  position or mount  the 
cabinet where it can tip over and fall on someone.  Do not attempt to mount the cabinet on 
speaker stands.  Do not attempt to ‘fly’ (suspend by cables, chains, ropes, etc.) the cabinet.  
It  was  not  designed  for  flying.    Position  it  only  on  a  flat,  stable  surface  where  it  is  not  in 
danger of tipping over. 

 

 

                     Also, note that the placement of the cabinet relative to floors and walls will affect the low 

frequency response.  Placing it closer to the floor and walls will reinforce the low frequency 
response.    Also,  make  sure  that  adequate  space  (at  least  6  inches)  is  left  behind  the 
cabinet for airflow over the internal amplifier heatsink. 
 
A  pole  mount  socket  is  provided  on  the  top  of  the  SA115  for  mounting  one  of  ISP 
Technologies Active Series Tripower 12 or Tripower 12XL three-way speakers.  A standard 
1.5-inch  pole  is  required  for  mounting  the  Tripower  speakers.    To  avoid  accidents  and 
insure stability this pole length should not exceed 2 feet in length.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание SA115












Отзывы: