ISHIDA IP-AI Скачать руководство пользователя

Страница: 5 / 139

• Be sure to install the printer unit and
the weighing unit on level ground.

Install the four rubber feet of the printer unit on

the

mount.

Accurate weighing cannot be made if the

weighing unit is not horizontally installed.

If the printer unit or the weighing unit falls over, it

may result in injury.

• Always use the specifi ed voltage.

•

Prepare a dedicated power source and always

use a power supply with rated voltage. Never

connect the machine power input with an AC

power supply exceeding the rated voltage.

• To avoid any potential electrical shock, ensure

that the protective ground wire is connected to

the main grounding provision.

• A power supply that generates voltage variation

may cause a malfunction, or using the machine

outside of the rated voltage may result in

machine failure or danger such as electric

shock.

• The equipment disconnect device is considered

to be: Plug, Appliance inlet.

• Replacement of fuses is limited only by service

personnel. Service personnel should refer to

service documentation for instructions for the

replacement.

• Replacement of Battery is limited only by

service personnel.

* To Service personnel:

Risk of Explosion if Battery is replaced by an

Incorrect Type. Dispose of Used Batteries

According to the Instructions.

•  Ensure that the printer unit, display
  unit and terminals do not come into
  contact with water.

If water comes in contact with these units or

terminals, this may cause a fi re.

PRECAUTIONS FOR USE

For safe operation, the following safety considerations must be observed:

Содержание IP-AI












































































































































Результаты поиска

Содержание IP-AI

Отзывы:

Похожие инструкции для IP-AI

Бренды по названию

Популярные бренды

ISHIDA IP-AI, Руководство по эксплуатации

Результаты поиска

Содержание IP-AI

Отзывы:

Похожие инструкции для IP-AI

Бренды по названию

Популярные бренды