ISHIDA IP-AI Скачать руководство пользователя страница 3

Страница: 3 / 139

III

IMPORTANT NOTICE

CHANGE IN SPECIFICATIONS

ERRORS AND OMISSIONS

LIMITATIONS OF LIABILITY

Thank you for purchasing the ISHIDA IP-AI.

This manual explains the procedures to install, operate, and maintain the machine.

Those who handle the machine must be aware of the hazards involved. These dangers may not be obvious, so

it is imperative to follow the instructions detailed in this manual when installing, operating, and maintaining the

machine. Therefore, we recommend that you thoroughly read and understand this manual before installing,

operating, or maintaining the machine, and keep this manual in a safe place where you can refer to it whenever

necessary.

Safety countermeasures should be carefully considered and implemented before performing any installation,

operation, or maintenance procedure not specifi cally described in this manual or indicated on the machine itself.

ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insuffi cient caution,

unauthorized modifi cations to the machine, or failure to follow the instructions contained in this manual.

Machine specifi cations and accessories may be changed at any time due to improvements or other reasons.

Consult with your ISHIDA representative at any time to confi rm the actual specifi cations of the purchased

machine.

The information in this manual has been carefully checked and is believed to be accurate. However, please

understand that the descriptions in this manual may not agree with the actual machine due to machine

improvements. The information is subject to change without prior notice in the future. ISHIDA assumes no

responsibility for clerical, typographical or proofreading errors, or omissions.

ISHIDA assumes no responsibility for special, indirect, or consequential damages, loss of profi ts or commercial

loss in any way connected with the machine, whether such claim is based on contract, warranty, negligence,

or strict liability.

ISHIDA shall assume responsibility for problems with the machine or the system based on an individual

maintenance contract. However, ISHIDA shall not be responsible for secondary problems.

ISHIDA assumes no responsibility for the user's programming of this machine, or any consequence thereof.

In no event shall ISHIDA be responsible for warranty, repair, or other claims regarding the machine unless

ISHIDA’s analysis confi rms that the machines were properly handled, stored, installed, and maintained and not

subject to contamination, abuse, misuse, or inappropriate modifi cation or repair.

Содержание IP-AI












































































































































Результаты поиска

Содержание IP-AI

Отзывы:

Бренды по названию

Популярные бренды

ISHIDA IP-AI, Руководство по эксплуатации

Результаты поиска

Содержание IP-AI

Отзывы:

Бренды по названию

Популярные бренды