ISGM i-2UVA Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

ISGM i-2UVA Скачать руководство пользователя страница 33

33

Product Version 1.0 | Revision A | Released 2022-2-21

SGM VACUUM TEST KIT

The Vacuum Test Kit is an accessory suitable for all SGM IP-rated
fixtures, made for testing the IP integrity upon reassembly.
In order to ensure the IP-rating of the

i-6

Series, it’s highly recom

-

mended that the fixture is always vacuum tested after installing or
swapping any part that might compromise the IP-rating, e.g.,
swapping the front lens.
SGM disclaims liability for any damage occasioned by the non-use,
or inability to use, the vacuum test kit after reassembling the fix

-

ture.

USB - XLR UPLOADER CABLE

The SGM USB to DMX cable is an accessory used mainly to update
the fixture with the latest SGM firmware. See below how to update
the fixture with the latest firmware.
The SGM Uploader cable is also used for controlling the DMX val

-

ues channel by channel through the Firmware Uploader Tool soft

-

ware (available for download at www.sgmlight.com).

Figure 28: SGM Vacuum Test Kit

Figure 29: SGM Uploader Cable

MAINTENANCE

Figure 26: i-2 UVA Anti-glare Shields

Figure 27 : i-2 UVA Anti-glare Shields

ANTI-GLARE SHIELDS

The i-2 UVA features two different types of optional anti-glare shields:

•

Full anti-glare shield - covers the full fixture’s opening.

•

Half anti-glare shield - covers half of the fixture’s opening.

Using the anti-glare shields will remove any unwanted glare and re

-

flections.
The anti-glare shields are easily mounted by removing the two tilt
lock bolts, one on each side of the fixture. Refit the anti-glare shield
in position and screw both tilt lock bolts again.

PLEASE NOTETHIS ACCESSORY IS SUITABLE FOR BOTH PERMA

-

NENT OUTDOOR AND INDOOR INSTALLATIONS.

FOR FURTHER INFORMATION AND OTHER POSSIBILITIES SEE
WWW.SGMLIGHT.COM OR CONTACT YOUR LOCAL SGM DEALER.

«
...
31
32
33
34
35
...
»

Содержание i-2UVA









































Отзывы:

Нет отзывов