manualshive.com logo in svg

Iseki SCMA48F, Руководство по введению

Поделиться
Скачать
Iseki SCMA48F Скачать руководство пользователя страница 37

CHAPTER 9. SMM54 INSPECTION AND MAINTENANCE OF MAJOR PARTS

37

 9

IMPORTANT: 

・

Be sure to install the belt as illustrated. 

・

An improperly installed belt will not work as expected 
but also may result in the belt breaking right away. 

・

Be sure to use following ISEKI’s genuine belts: 

  SMM54 8657-203-001-00 (VB101) 

d.  Make sure the belt is seated properly in the groove 

of each pulley and apply tension to it by expand-
ing the tension spring properly with the tension rod 
referring to the paragraph for “Inspection of belt ten-
sion.” 

e.  Re-instaII the drive shaft cover and belt covers. 

CAUTION: Never forget to replace the re-
moved belt covers and drive shaft cover. 

3.  INSPECTION & REPLACEMENT OF BLADES 

・

Inspection of blades 

a.  Apply the parking brakes. 

CAUTION: Be sure to apply the parking 
brake securely. 

b 

Start the engine and turn the throttle lever to the low 
speed (

t

) position to decelerate the engine.

c.  Shift the lift lever to the UP (

u

) position and raise 

the mower deck to the highest position. 

d.  Stop the engine. 

・

Inspection of belt 

a.  Remove the drive shaft cover and both the belt cov-

ers installed on the mower deck.

(1)  Belt cover (LH)  

(3)  Drive shaft cover 

(2)  Belt cover (RH) 

b.  Check the belt for damage and dirt.
 

If it is smeared with oil or dirt, or wet with water, 
wipe it clean with a dry cloth. When damaged, in-
stall a new belt.

CAUTION: Never forget to replace all the re-
moved covers. 

・

Replacement of the belt 

a.  Remove the drive shaft cover and belt covers (RH 

and LH) from the mower deck. 

b.  Loosen the lock nut of the tension rod and remove 

the tension spring. 

(1) Belt 

c. 

Remove the belt and install a new belt.

1

2

3

1

Содержание SCMA48F





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды