4
5
（Figure 3）
VII. Fault Handling
Fault Inspection Solution
The air
pump
cannot be
started
normally.
1. The power source
is not plugged
properly.
2. The fuse in DC
plug (7) is burnt out.
3. Overheating or
overload causes
motor stop.
1. Check whether
the hose is blocked
or cracked.
2. The joint between
the hose and air
pump or air bag is
not installed
properly.
1. Make sure that the power wire is
plugged in the 12V DC socket.
2. Change the fuse.
3. Cool the motor and restart it.
4. If the problem cannot be solved,
please contact with the
manufacturer or its service agent or
the similar authorized personnel.
1. Change the hose or make it
unblocked, and check whether the
hose is cracked.
2. Reinstall the hose.
3. If the problem cannot be solved,
please contact with the
manufacturer or its service agent or
the similar authorized personnel.
Slow or
abnormal
inflation.
VIII. Maintenance and Storage
After using, or if you want to move, maintain or adjust the product,
please first pull out the DC plug from the socket.
when it is idle, it shall be properly stored after being fully cooled.
It shall not be exposed to the rain or immersed in water.
Please store it in the dry and ventilated place.
IX. Suggestions
The warranty period of this product is one year, and it is suggested to
use the original accessories. For any fault not caused by using the
original accessories, it shall be out of the warranty scope.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Notice: The factory set pressure value of the air pump is 10PSI
(10PSI=0.689BAR), and at the time of the secondary use, the set
pressure value for the last time use will be displayed by default.
Notice: After powered on, if there is no operation within 2 minutes, the
air pump will enter standby mode, and the machine can be initiated
by pressing the power switch button
VI. Precautions
The applied power source must be the 12V DC power source (as
Figure 3).
Don't block the air inlet (10) at the bottom of the air pump, and
guarantee air inlet (10) to be always unblocked.
Observe the local waste treatment provisions, and it is not allowed
to throw the air pump away randomly.
Don't use this product when the hose is damaged, and please
change the hose immediately.
Don't pull out the hose when inflating, because that the high
pressure may hurt the physical body.
Don't make the air pump work for more than 15 minutes, because
that motor overheating may cause internal damage; and the air
pump shall be fully cooled for 30 minutes after continuously working
up to 15 minutes.
Please don't use this air pump if any part is damaged, and please
contact with the professional personnel to repair it.
This product shall not be exposed to the rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward to face
or body.
Please don't not leave while inflating.
.
HT-786 DC12V
HT-786 DC12V
4
5
（Figure 3）
VII. Fault Handling
Fault Inspection Solution
The air
pump
cannot be
started
normally.
1. The power source
is not plugged
properly.
2. The fuse in DC
plug (7) is burnt out.
3. Overheating or
overload causes
motor stop.
1. Check whether
the hose is blocked
or cracked.
2. The joint between
the hose and air
pump or air bag is
not installed
properly.
1. Make sure that the power wire is
plugged in the 12V DC socket.
2. Change the fuse.
3. Cool the motor and restart it.
4. If the problem cannot be solved,
please contact with the
manufacturer or its service agent or
the similar authorized personnel.
1. Change the hose or make it
unblocked, and check whether the
hose is cracked.
2. Reinstall the hose.
3. If the problem cannot be solved,
please contact with the
manufacturer or its service agent or
the similar authorized personnel.
Slow or
abnormal
inflation.
VIII. Maintenance and Storage
After using, or if you want to move, maintain or adjust the product,
please first pull out the DC plug from the socket.
when it is idle, it shall be properly stored after being fully cooled.
It shall not be exposed to the rain or immersed in water.
Please store it in the dry and ventilated place.
IX. Suggestions
The warranty period of this product is one year, and it is suggested to
use the original accessories. For any fault not caused by using the
original accessories, it shall be out of the warranty scope.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Notice: The factory set pressure value of the air pump is 10PSI
(10PSI=0.689BAR), and at the time of the secondary use, the set
pressure value for the last time use will be displayed by default.
Notice: After powered on, if there is no operation within 2 minutes, the
air pump will enter standby mode, and the machine can be initiated
by pressing the power switch button
VI. Precautions
The applied power source must be the 12V DC power source (as
Figure 3).
Don't block the air inlet (10) at the bottom of the air pump, and
guarantee air inlet (10) to be always unblocked.
Observe the local waste treatment provisions, and it is not allowed
to throw the air pump away randomly.
Don't use this product when the hose is damaged, and please
change the hose immediately.
Don't pull out the hose when inflating, because that the high
pressure may hurt the physical body.
Don't make the air pump work for more than 15 minutes, because
that motor overheating may cause internal damage; and the air
pump shall be fully cooled for 30 minutes after continuously working
up to 15 minutes.
Please don't use this air pump if any part is damaged, and please
contact with the professional personnel to repair it.
This product shall not be exposed to the rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward to face
or body.
Please don't not leave while inflating.
.
HT-786 DC12V
HT-786 DC12V
EN
EN
