IRT VA-700 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 23

IRT VA-700 Скачать руководство пользователя страница 22

EQ-1227

VA-700

I.R.T. Communications Pty Ltd | www.irtcommunications.com

Page 22 of 23

Revision 10

INSTALLATION

Installation in VA-700 VDA:

If the slider selector switch is to be fitted, the PCB track connecting one side of switch SW 1 should be cut before
mounting the switch on the circuit board of the VA-700.

The switch will now choose between the sub-module equalisation and that of the main board. Switch position 1
refers to the main equaliser and position 2 to the EQ-1227 equaliser.

If only EQ-1227 equalisation is to be required the PCB track connecting one side of switch SW 1 should be cut and a
link soldered between the centre contact of the switch position and the other side.

The correct orientation for the EQ-1227 is with the component side facing the EQ range selection links 8a / 8b on
the VA-700.

When mounting the EQ-1227 sub board care should be taken to ensure that the pins of PL 1 on the VA-700 are
correctly mating with the socket on the EQ-1227 before pressing the EQ-1227 firmly down.

The VA-700T comes equipped with the EQ-1227 and slider switch already fitted.

«
...
20
21
22
23
»

Содержание VA-700
























Отзывы:

Нет отзывов