IRT DTR-4630 Скачать руководство пользователя страница 6

 

DTR-4630 

I.R.T. Communications Pty Ltd | www.irtcommunications.com 

 

 

Page 6 of 17

 

Revision 02 

TECHNICAL SPECIFICATIONS

 

Transmitter: 

Input serial data signal

 

2.97 Gb/s (3G-SDI) to SMPTE 424M; 

 

1.485 Gb/s (HD-SDI) to SMPTE 292M; 

 

270 Mb/s (SD-SDI) to SMPTE 259M-C and DVB-ASI. 

Input impedance

 

75 Ω. 

Input return loss

 

> 15 dB 5 MHz to 1.5 GHz; 

 

> 10 dB 1.5 GHz to 2.97 GHz. 

Automatic cable compensation

 

> 100 m at 2.97 Gb/s (3G-SDI) with Belden 1694A (typ. 110m); 

 

> 100 m at 1.485 Gb/s (HD-SDI) with Belden 1694A (typ. 160m); 

 

> 250 m at 270 Mb/s (SD-SDI/ASI) with Belden 8281 (typ. >300m). 

Input connector

 

2  x  BNC  on  rear  panel, with IN 1 taking priority & IN 2 automatically switching in on 
loss of IN 1. 

Output connector

 

1 x BNC (OUT 1) on rear panel, link selectable Tx input monitor, or nil if set as a second Rx output. 

 

Receiver: 

Number of outputs

 

2 data reclocked, 

 

AC coupled. 

Output level

 

800 mV ± 10%. 

Output impedance

 

75 Ω. 

Output return loss

 

> 15 dB 5 MHz to 1.5 GHz; 

 

> 10 dB 1.5 GHz to 2.97 GHz. 

Output rise and fall time

 

< 135 ps at 2.97 Gb/s and 1.485 Gb/s; 

 

> 0.4 ns and < 1.5 ns at 270 Mb/s. 

Intrinsic jitter

 

< 0.3 UI at 2.97 Gb/s reclocked; 

 

< 0.2 UI at 1.485 Gb/s reclocked; 

 

< 0.1 UI at 270 Mb/s reclocked. 

Output connector

 

2 x BNC on rear assembly, or 1 x BNC if OUT 1 has been link selected as an input monitor. 

 

Optical:

 

Optical output

 

0 dBm +4.5/-0 dB CWDM DFB laser. 

Optical input

 

APD detector, -9 to -27 dBm input level at 3G-SDI, typically < -30 dBm at HD/SD-SDI. 

 

PIN detector, -3 to -18 dBm input level at 3G-SDI, typically < -20 dBm at HD/SD-SDI. 

Available wavelengths

   

1310nm or 1550nm. Other wavelengths available upon request. 

Optical path loss

4, 5

 

9 to 27 dB at 3G-SDI, typically >30 dB at HD/SD-SDI, APD detector; 

 

3 to 18 dB at 3G-SDI, typically >20 dB at HD/SD-SDI, PIN detector. 

 

(Optical path loss = Laser O/P power – Detector I/P power) 

Optical fibre

 

Designed for use with 9/125 μm single mode fibre. 

Optical connector

 

2 x SC/PC (standard) on rear – direct connection to main card, 1 Tx and 1 Rx; or 

 

1 x SC/PC (standard) with WDM option fitted. 

 

Power Requirements:

 

 

Voltage

 

28 Vac CT (14-0-14) or 

±

16 Vdc. 

Power consumption

 

< 5.0 VA. 

 

Other: 

Temperature range

 

0 - 50° C ambient. 

Mechanical

 

For mounting in IRT 19" rack chassis with input, output and power connections on the 
rear panel. 

Finish 

Front panel

 

Grey, black lettering & red IRT logo. 

 

Rear assembly

 

Detachable silk-screened PCB with direct mount connectors to Eurocard and external 
signals. 

Dimensions

 

6 HP x 3 U x 220 mm IRT Eurocard. 

Optional accessories

 

On-board 1310/1550nm WDM

6

 combiner. 

 

WDM order codes

 

DTR-4630/1310/WDM & DTR-4630/1550/WDM. 

 

 

 

NOTE:

 

4

 

Typical  values  based  using  DFB  laser.  Optical  attenuator  supplied  for  when  optical 
path loss is less than 3dB for PIN detector and 9dB for APD detector. 

 

 

5

 

With  WDM  option  fitted  for  combined  use  on  a  single  fibre,  optical  path  loss  is 
reduced by approximately 2dB. 

 

 

With  WDM  module  fitted,  when  operating  as  a  pair,  one  DTR-4630  must  be  fitted 
with a 1310nm laser and the other a 1550nm laser.

 

 

Due to our policy of continuing development, these specifications are subject to change without notice. 

Содержание DTR-4630


















Отзывы: