IRT DTR-4630 Скачать руководство пользователя страница 5

 

DTR-4630 

I.R.T. Communications Pty Ltd | www.irtcommunications.com 

 

 

Page 5 of 17

 

Revision 02 

GENERAL DESCRIPTION

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
The  IRT  DTR-4630  is  a  transmit/receive  (transceiver)  module  designed  principally  for  use  as  a  serial  data  fibre  optic 
transmission  link  for  3G-SDI,  HD-SDI  or  SD-SDI  applications  conforming  to  SMPTE  standards  424M,  292M  and  259M-C 
using  9/125  μm  single  mode  fibre.  This  enables  the  use  of  space  saving  fibre  optic  cable  for  reliable  transmission  of 
digital video signals over lengths greater than can be achieved with coaxial cable. 

 

In  addition,  the  link  may  be  used  for  ASI  transport  streams  for  use  with  MPEG  compressed  video  streams  or  other 
270 Mb/s type data. 

 

The  transmitter  section  features  automatic  input  cable  equalisation.  LED  indicators  are  provided  for  digital  signal 
presence and rate, DC power and LASER failure. 

 

A “keep link alive” signal is available to maintain optical link operation when no electrical input is present. 

 

Two inputs are provided with automatic changeover to input 2 on loss of input 1 for input signal redundancy. 

 

The  receiver  section  uses  a  choice  of  either  a  PIN  photodiode  or  APD  detector  with  signal  conditioning  and  reclocking

 

circuits. The data rate is automatically set to match the 3G-SDI, HD-SDI or SD-SDI/ASI rates dependent on the actual input 
data rate to the transmitter. 

 

Two  serial  digital  outputs  are  provided.  LED  indicators  are  provided  for  digital  signal  presence  &  type,  optical loss and 
power. 

 

Relay contact outputs are also provided for external use of alarm signals. 

 

The  DTR-4630  can  be  used  as  an  independent  transmitter  and  receiver  at  the  same  time  allowing  bi-directional 
operation  over two single mode fibres. Being independent from each other, the transmit and receive signals can be of 
mixed signal types. 

 

Optionally a 1310/1550nm WDM

2, 3

 optical combiner can be fitted to allow for combined use on a single fibre. 

 

SNMP (Simple Network Management Protocol) is available for remote monitoring when used in conjunction with an IRT 
frame fitted with SNMP capability. 

 

Standard features: 

 

Transports 3G-SDI, HD-SDI, SD-SDI or ASI signal rates. 

 

Single or bi-directional operation possible with independent transmit and receive functions on the one card. 

 

Path lengths up to 30 dB

1

 optical path loss using 9/125μm single mode fibre. 

 

Automatic changeover switching  of input for signal redundancy on Tx. 

 

LED indicators and external alarm contacts. 

 

Fibre, video and alarm connections at rear. 

 

Remote monitoring via SNMP. 

 

Optional on-board WDM

2, 3

 optical combiner for use on a single common fibre. 

 

NOTE:

 

1

  27dB path loss at 3G. Typically >30dB at HD and SD. Fitted with APD detector. 

 

2

  With WDM option fitted for combined use on a single fibre, optical path loss is reduced by approximately 2dB. 

 

3

  With WDM option fitted, when operating as a pair, one DTR-4630 must be fitted with a 1310nm laser and 

the other a 1550nm laser. 

BLOCK DIAGRAM DTR -4630 SIGNAL PATH 

Fibre Link 

9-27

*

dB path loss at 3G 

(>30dB at HD and SD) 

NOTE: * Fitted with APD detector. 3-18dB when fitted with PIN detector. 

DTR-4630 

(Tx/Rx) 

I/P 1 
I/P 2 

Fibre O/P 

Fibre I/P 

O/P 1 
O/P 2 

 
 

Alarm O/P 

DTR-4630 

(Tx/Rx) 

O/P 1 
O/P 2 

Fibre I/P 
Fibre O/P 

I/P 1 
I/P 2 

 
 

Alarm O/P 

SNMP 

SNMP 

3G-SDI 

HD-SDI 

SD-SDI 

ASI 

3

G-SDI 

HD-SDI 

SD-SDI 

ASI 

3G-SDI 
HD-SDI 
SD-SDI 
ASI 

3G-SDI 
HD-SDI 
SD-SDI 
ASI 

Содержание DTR-4630


















Отзывы: