IRT DDA-4280 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 17

IRT DDA-4280 Скачать руководство пользователя страница 15

4280-dda.ib.rev0.doc

Page 15 of 17

11/03/2009

SNMP with IRT Products:

IRT Electronics currently employs SNMPv1 with its SNMP capable frames. The frame acts as an

agent

when fitted

with a CDM-xxxx module. This module has its own designated slot next to the power supply so as to not affect the
number of modules that the frame will take. Communication between the

NMS

, the frame and its loaded modules are

via this CDM-xxxx module. Note that the

NMS

software is third party and not supplied by IRT Electronics.

Ethernet connection for SNMP operation is via an RJ45 connector on the rear of the frame, below the mains inlet.
Ethernet rate runs at either 10 baseT or 100 baseT.

Frame parameters, such as Name, Address and Location, are set via an RS232 interface, a D9 connector on the rear
of the frame below the mains inlet. A software terminal emulator, such as Tera Term or HyperTerminal, is used for
setting and reading the parameters of the frame.

IRT modules that are SNMP compatible need a plug-in SMU-4000 module with a program relevant to the module
that it is plugged into. Depending on the module, besides the module identification, parameters such as alarm states,
inputs and controls etc. are communicated to the CDM-xxxx

agent

via a data bus on the rear of the frame. Thus the

CDM-xxxx collects information on what is loaded within the frame, what positions they occupy, and their current
status for communication to the

NMS

when the

NMS

sends a request for information.

In the event of a major alarm from any of the SNMP compatible modules, or power supplies, a

trap

is automatically

sent by the CDM-xxxx

agent

to the

NMS

without any prompting by the

NMS

. This alerts the operator to any fault

conditions that may exist that need immediate attention.

FRU-4000

FRAME

110/240 V 50/60 Hz

0.7 A (max.)

FUSES

110/120 Vac

1A S.B.

220/240 Vac

500 mA S.B.

AS3260 approval no.: CS6346N
Ass. no.: 804692

+

-

48Vdc

Alarm

RS232

Ethernet

IRT SNMP Connections

IRT modules fitted

with SMU-4000

PSU’s

CDM-xxxx

IRT SNMP Frame

IRT SNMP Frame

IRT modules fitted

with SMU-4000

PSU’s

CDM-xxxx

Network

Ethernet Cable

Ethernet Cable

Ethernet Cable

NMS

IRT SNMP Setup

«
...
13
14
15
16
17
»

Содержание DDA-4280


















Отзывы:

Нет отзывов