IRT DDA-4006 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 13

IRT DDA-4006 Скачать руководство пользователя страница 9

4006-dda.ib.rev1.doc

Page 9 of 12

10/09/2008

SNMP with IRT Products

IRT Electronics currently employs SNMPv1 with its 4000 series frame. The frame acts as an

agent

when fitted with

a CDM-4000 module. This module has its own designated slot next to the power supply so as to not affect the
number of modules that the frame will take. Communication between the

NMS

, the frame and its loaded modules

are via this CDM-4000 module. Note that the

NMS

software is third party and not supplied by IRT Electronics.

Ethernet connection for SNMP operation is via an RJ45 connector on the rear of the frame, below the mains inlet.
Ethernet rate runs at either 10 baseT or 100 baseT.

Frame parameters, such as Name, Address and Location, are set via an RS232 interface, a D9 connector on the rear
of the frame below the mains inlet. A software terminal emulator, such as Tera Term or HyperTerminal, is used for
setting and reading the parameters of the frame.

IRT modules that are SNMP compatible need a plug-in SMU-4000 module with a program relevant to the module
that it is plugged into. Depending on the module, besides the module identification, parameters such as alarm states,
inputs and controls etc. are communicated to the CDM-4000

agent

via a data bus on the rear of the frame. Thus the

CDM-4000 collects information on what is loaded within the frame, what positions they occupy, and their current
status for communication to the

NMS

when the

NMS

sends a request for information.

In the event of a major alarm from any of the SNMP compatible modules, or power supplies, a

trap

is automatically

sent by the CDM-4000

agent

to the

NMS

without any prompting by the

NMS

. This alerts the operator to any fault

conditions that may exist that need immediate attention.

FRU-4000

FRAME

110/240 V 50/60 Hz

0.7 A (max.)

FUSES

110/120 Vac

1A S.B.

220/240 Vac

500 mA S.B.

AS3260 approval no.: CS6346N
Ass. no.: 804692

+

-

48Vdc

Alarm

RS232

Ethernet

IRT SNMP Connections

IRT modules fitted

with SMU-4000

PSU’s

CDM-4000

IRT 4000 Series Frame

IRT 4000 Series Frame

IRT modules fitted

with SMU-4000

PSU’s

CDM-4000

IP

Network

Ethernet Cable

Ethernet Cable

Ethernet Cable

NMS

IRT 4000 Series SNMP Setup

IRT

Communications

www.irtcommunications.com

«
...
7
8
9
10
11
...
»

Содержание DDA-4006














Отзывы:

Нет отзывов