background image

4170-ams.ib.rev0.doc 

Page 3 of 14 

09/09/2005 

IRT Eurocard 

AMS-4170/AMS-4170T 

2 x 2 relay switcher 

for SDI, G.703 or analogue video 

AES, RS422 or stereo audio signals 

 

General Description

 

 

 

The AMS-4170 consists of one “video” and two “balanced audio” switches. Each switch is arranged as a changeover 
set with two inputs and two outputs. No terminations are provided on the board allowing the switcher to be used in a 
wide variety of applications and with signals of various types and impedances. 

 

The “video” path uses enhanced performance relays to provide switching capabilities for high-speed data signals up 
to 270 Mb/s and may be used with analogue video, SDI, MPEG or RF signals. When used with SDI and high-speed 
data signals all cable lengths should be kept to a minimum. For best performance the outputs should be connected to 
inputs with automatic cable equalisation. 

 

The “audio” path may be used for balanced or unbalanced audio or control signals (RS232, RS422, RS485 etc). The 
audio circuit uses two relays in series to provide excellent isolation between the two states. 

 

The AMS-4170 is ideally suited to applications where a simple choice between two inputs or outputs is required and 
may be easily driven by audio, video or other detector circuits for automatic path selection. 

 

Each switch is equipped with its own transistor driver circuit, which may be bypassed for direct operation of the 
relay if desired. Links allow any of the three driver circuits to operate more than one of the sets of relays. 

 

Front panel LED indicators are used to indicate the status of each relay circuit. 

 

The AMS-4170T version also consists of front panel switches to allow a choice of local or remote control operation. 
Unless otherwise stated, all aspects of the AMS-4170T in this manual are the same for the AMS-4170. 

 

An optional SNMP (Simple Network Management Protocol) plug-in module is available for remote monitoring and 
control when used in conjunction with IRT’s 4000 series frame fitted with SNMP capability. 

 

The AMS-4170 is designed to fit IRT’s standard Eurocard frames as well as IRT’s 4000 series frame for use with 
IRT’s SNMP system and may be used alongside any other of IRT’s analogue or digital Eurocards. 

 

Standard features: 

• 

One video and two balanced audio changeover switches in one package. 

• 

Video path suitable for SDI (270 Mb/s), analogue video, MPEG data streams @ 2, 8, 34, 45, 144 Mb/s. 

• 

Audio path suitable for 2 balanced audio or data signals or 4 unbalanced audio or data signals. 

• 

Married or independent operation 

• 

Default path on power fail. 

• 

TTL or direct relay switching. 

• 

Optional plug in SNMP monitoring and control module. 

• 

Front panel LED status indicators. 

VIDEO A I/P

AMS-4170 FUNCTIONAL BLOCK DIAGRAM

VIDEO B I/P

VIDEO A O/P

VIDEO B O/P

AUDIO B (L) O/P

AUDIO A (L) O/P

AUDIO B (L) I/P

AUDIO A (L) I/P

AUDIO B (R) O/P

AUDIO A (R) O/P

AUDIO B (R) I/P

AUDIO A (R) I/P

SNMP 

IRT 

Communications 

www.irtcommunications.com

Содержание AMS-4170


















Отзывы: