IronStrike 32FS Скачать руководство пользователя

Страница: 9 / 38

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Removing Appliance From Pallet

1. After removing the packaging from the stove, lift the hopper lid, and

remove all prepackaged items that were shipped in the hopper. Next,

open the stove door and remove all prepackaged items.

2. With the stove door open, remove the ash drawer and set aside. Using

a 7/16” socket or open end wrench, remove the front lag screw (see

Figure 5A

)

3. Using a 5/32" allen wrench remove the two screws in the rear pallet

bracket (see

Figure 5B

)

. Using a 7/16” socket or open end wrench,

remove the rear lag screw (see

Figure 5B

)

INSTALLATION

Front Lag Screw

(actual size)

Rear Lag Screw

(actual size)

Pallet

SEE DETAIL B

DETAIL B

SEE DETAIL C

DETAIL C

Rear Pallet

Bracket

Rear Lag Screw

Front Lag Screw

Figure 5A - Front Lag Screw

Figure 5B - Rear Lag Screw and Pallet Bracket

Installation Check List

It is strongly recommended that you have an IHP dealer install your stove.

If you install your stove yourself, you should review your installation plan

with an IHP dealer.

Check list:

Check off each item as you proceed with the installation process.

Read the ENTIRE stove installation section first

Determine the appropriate measurements and locations for your

installation.

Follow the installation directions in this manual.

Be sure to pre-fit all items before you install, fasten, or set up the

appliance permanently.

Measure for exhaust (also outside air tube when applicable) and mark

the location. Place the unit in place to make sure it's correct before

cutting holes in your wall.

Содержание 32FS







































Результаты поиска

Содержание 32FS

Отзывы:

Похожие инструкции для 32FS

Бренды по названию

Популярные бренды

IronStrike 32FS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 32FS

Отзывы:

Похожие инструкции для 32FS

Бренды по названию

Популярные бренды