IRIS IRMA 6 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 30

background image

IRMA6-SENSOR-HD-00-SWITCH-(IO)-00-(R)(1)

Installation Manual | Released

Rev. 1.4 | 12/2020

11

/ 27

3

Connecting IRMA 6 (optionally with angled M12 connectors)

Connect IRMA 6 to power supply

Connect IRMA 6 from component

to the on-board power supply via the wire strands of the power
supply cable K-M12POW-B-oE-04-2m.
Mind the correct connection points (+, - and shield) in the
connection block of the vehicle and See section "Ensuring
power supply", p. 14 for time relay for 30 min overrun power.

Connect IRMA 6 with Ethernet

Connect IRMA 6 from component

with the switch via the

M12 system Ethernet cable

K-M12CAT5-XX-xm

.

Via Ethernet

the connection to the OBU and to the service PC is made.

Only

possible with service PCs having an Ethernet interface.

1061818736_p

M12 power supply

connector (m)

Switch-M12-5-Port-eCon

M12 Ethernet

connector (f)

«
...
9
10
11
12
13
...
»

Содержание IRMA 6































Отзывы:

Нет отзывов

Похожие инструкции для IRMA 6

Бренд: Samsung Страницы: 27

Бренд: Samsung Страницы: 66

Бренд: Casio Страницы: 4

Бренд: Casio Страницы: 19

Бренд: Casio Страницы: 19

Бренд: GRG Banking Страницы: 71

Бренд: Hengstler Страницы: 7

Бренд: Labelmate Страницы: 18

Бренд: Magner Страницы: 18

Бренд: Olivetti Страницы: 8

Бренд: Sam4s Страницы: 324

CoinCo Guardian6000

Бренд: Envision Ware Страницы: 11

Бренд: JCM GLOBAL Страницы: 124

Бренд: Triton Страницы: 8

Lexic Rex 2000 HC2

Бренд: LEGRAND Страницы: 2

Бренд: Hotraco agri Страницы: 5

Бренд: BellCon Страницы: 36

Бренд: TEC Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды