IQ Power Tools iQ360XT Скачать руководство пользователя страница 11

Страница: 11 / 20

iQ360XT

Operator’s Manual

888-274-7744

www.iqpowertools.com

PORTABLE GENERATOR:

If using a portable generator to provide power, ensure

the generator meets the following requirements to

operate a tool requiring 20amp. A 3500 Watt or greater

generator is recommended.

PRE-START INSPECTION:

The pre-start inspection should be performed before

beginning any job.

NOTE: In order to avoid breaker tripping, a 20-amp circuit

breaker is highly recommended..

If the diamond blade shows signs of fatigue cracking,

replace the blade before starting work.

• Inspect Blade for damage (1). Verify that the Blade

is correct for the material being cut.

• Inspect other areas for damage, including Frame

Assembly (2), Handle (3), and Cord Assembly (4).

If an extension cord is used, first verify it meets the

requirements of TABLE 1.

DO NOT FORCE the blade to cut! It will do the job

better and safer at the rate for which it was designed.

SETUP, ADJUSTMENTS & OPERATION

5.1

CHOP SAW FEATURES

A. Lock Pin

B. Blade

C. Guard

D. Blade lock lever

E. Trigger Switch

TO CARRY:

Fold down unit to position where you can carry the saw.

Push in lock pin (A) to lock arm down.

UNLOCKING:

To unlock tool and raise head, depress motor arm

slightly and pull lock pin (A) out. Motor arm will then pivot

upward.

STARTING MACHINE

The saw power switch starts the saw motor and vacuum

motor simultaneously. To start the saw motor, press

the

POWER

switch

or on symbol. Defective switches

should be replaced by an authorized service workshop.

STOPPING MACHINE

To stop the saw motor, press the

POWER

switch

or off symbol.

FENCE OPERATION:

The Fence can be set two ways:

Содержание iQ360XT





















Результаты поиска

Содержание iQ360XT

Отзывы:

Похожие инструкции для iQ360XT

Бренды по названию

Популярные бренды

IQ Power Tools iQ360XT, Руководство оператора

Результаты поиска

Содержание iQ360XT

Отзывы:

Похожие инструкции для iQ360XT

Бренды по названию

Популярные бренды