background image

SECTION SIX

TROUBLESHOOTING GUIDE

PROBLEM

o

Lamp stays ON all the time at

night.

o

PIR keeps activating for no 

reason / at random.

o

PIR sensor will not operate at

all.

o

The PIR sensor will not 

operate at night.

o

Unit activates during the 

daytime

o

PIR coverage is poor/sporadic

Detection range varies from

day to day

o

Lamp flashes on/off on/off in a

regular pattern

SOLUTION

The unit may be suffering from false activation. Cover the
sensor lens completely with a thick cloth. This will prevent the
sensor from "seeing" anything. If the unit now switches off
after the set time duration and does not re-activate, this
indicates that the problem was caused by false activation. The
problem may be solved by slightly adjusting the
direction/angle of the sensor head (see previous section).
You may not be allowing the unit time to complete it's 
warm-up period. Stand well out of the detection range and
wait (the warm-up period should never exceed 5 minutes).
Occasionally, winds may activate the sensor. Sometimes
passages between buildings etc. can cause a "wind tunnel"
effect.
Ensure the unit is not positioned so as to allow detection of
cars/people using public thoroughfares adjacent to your
property.

Check that the power is switched ON at the circuit
breaker/internal wall switch.
Turn OFF the power to the unit and check the wiring
connections as per the diagram (see previous section 3).
Ensure no connections are loose.
Check the lamp. If the lamp has failed, replace. Ensure that
the lamp is seated correctly in the lampholder.

The level of ambient light in the area may be too bright to
allow operation at the current DUSK setting. During the hours
of darkness, adjust the DUSK control slowly clockwise until
the lamp illuminates. Refer to previous section for more
details.

The level of ambient light in the area may be too dark for the
current DUSK setting. During daylight, adjust the DUSK
control slightly anti-clockwise. When the lamp extinguishes,
enter the detection area. If the PIR still activates, the setting is
still too high. Repeat the above procedure until the PIR does
not activate when you enter the detection area. Refer to
previous section for more details.

Unit may be poorly located. See previous section - ‘Selecting
The Location’ and re-locate the unit.
PIR sensors are influenced by climatic conditions. The colder
the ambient temperature, the more effective the sensor will
be. You may need to make seasonal adjustments to the
sensor head position to ensure trouble-free operation all year
round.
The PIR is sensing illumination from its own lamp, turning it off
as if it were daylight every time the lamp illuminates. Turn the
LUX setting clockwise until the flashing stops

SF-73CA180-150-D.qxd  16/05/2005  11:20  Page 10

Содержание E-614












Отзывы: