ioWave ioLink 4 Скачать руководство пользователя страница 67

Страница: 67 / 69

PRELIMINARY

C-1

C.1 FCC Regulatory Notice

This equipment complies with FCC Regulation 15.247, which specifies the license-free operation of direct

sequence, spread-spectrum wireless communications devices. This device operates in the 2.4 to 2.4835

GHz frequency band reserved for industrial, scientific and medical applications. Since this device

generates radio frequency waves, it may interfere with other radio signals in the same area unless the

proper installation and operations procedures are followed. It has been proven in testing that this device

complies within the limits of FCC Regulations that are designed to provide reasonable protection against

such interference in a commercial environment.

NOTE:

Installation and maintenance must be performed by authorized

ioWave

personnel or those

persons properly trained and authorized to do such procedures.

ioWave

is not responsible for any

damages, incidental or otherwise, in connection with use of this manual by anyone not described above.

C.2 Warranty

ioWave, Inc.

manufactured products are warranted to be free from material defect in material and

workmanship under normal use for a period of one (1) year from the date of shipment. This warranty

extends only to products manufactured by

ioWave, Inc.

and is expressly conditioned upon the equipment

having been installed in accordance with the standard installation and configuration practices

recommended by

ioWave

, by authorized

ioWave

personnel or those persons certified and authorized to

do such procedures, and the equipment having been maintained in accordance with

ioWave

recommended standard maintenance practices.

APPENDIX C IMPORTANT INFORMATION ABOUT YOUR SYSTEM

Содержание ioLink 4






































































Результаты поиска

Содержание ioLink 4

Отзывы:

Бренды по названию

Популярные бренды

ioWave ioLink 4, Руководство пользователя

Результаты поиска

Содержание ioLink 4

Отзывы:

Бренды по названию

Популярные бренды