INVT GD10-0R2G-2-B Скачать руководство пользователя страница 6

Страница: 6 / 125

Goodrive10 Series Mini VFD

Safety precautions

-1-

1 Safety precautions

Read this manual carefully and follow all safety precautions before moving, installing,

operating and servicing the variable-frequency drive (VFD). If ignored, physical injury or
death may occur, or damage may occur to the devices.

If any physical injury or death or damage to the devices occurs for ignoring to the safety

precautions in the manual, our company will not be responsible for any damages and we
are not legally bound in any manner.

1.1 Safety definition

Danger:

Serious physical injury or even death may occur if related
requirements are not followed.

Warning:

Physical injury or damage to the devices may occur if related
requirements are not followed.

Note:

Physical hurt may occur if related requirements are not followed.

Qualified
electricians:

People working on the device should take part in professional

electrical and safety training, receive the certification and be

familiar with all steps and requirements of installing,

commissioning, operating and maintaining the device to avoid
any emergency.

1.2 Warning signs

Warnings caution you about conditions which can result in serious injury or death and/or

damage to the equipment, and advice on how to avoid the danger. Following warning
symbols are used in this manual:

Sign

Name

Instruction

Abbreviation

Danger

Serious physical injury or even death

may occur if related requirements are

not followed

Warning

Physical injury or damage to the

devices

may

occur

requirements are not followed

Do not touch

Electrostatic

discharge

Damage to the PCBA board may occur

if related requirements are not followed

Hot sides

Sides of the device may become hot.

Do not touch.

Содержание GD10-0R2G-2-B






























































































































Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды

INVT GD10-0R2G-2-B, Руководство по эксплуатации

Результаты поиска

Содержание GD10-0R2G-2-B

Отзывы:

Похожие инструкции для GD10-0R2G-2-B

Бренды по названию

Популярные бренды