3
Thank you for purchasing Inverto’s advanced Unicable II multiswitch and we are certain it will
meet your expectations. Before installing and operating the product, please read the following
instructions and recommendations. We suggest that you keep this manual for future use.
Warranty
This Unicable II multiswitch is designed for the distribution of satellite and terrestrial television
and radio signals in home installations. The warranty does not apply for products used for other
purposes than those specified herein. The user/installer shall be responsible for any damage in-
curred as a result of not using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface. The product shall be
in no case held only with the connected cables. Place the product in a dry environment where
it is not exposed to rain or running water. Do not install the product close to heat sources or in
places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
To connect the product inputs and outputs use high-quality coax-
ial cables designed for satellite reception and F-connectors. Use a
highly shielded coaxial cables with minimum shielding of 90dB. If
you use wall sockets to loopthrough the Unicable II output, make
sure the wall sockets were designed for satellite reception com-
patible with Unicable technology and allows bidirectional signal
propagation. The multiswitch can be powered over any of its out-
put ports by any of the connected STBs if it is able to supply the
necessary power to the switch and the Quattro/Wideband LNB
connected to it. If none of the connected STBs can supply suffi-
cient power, the multiswitch shall be powered by the supplied AC/
DC adapter and Power Inserter over its Unicable II port.
Default product configuration
The satellite input ports of the Multiswitch are configured to support a universal Quattro LNB by
default.
The default configuration of the output ports is as marked on the device’s label. By de fault - (i)
the Unicable II port operates in dynamic mode (compatible with EN50494/EN50607) and sup-
ports up to 32 User Bands. This allows to connect up to 32 receiver tuners - each to be assigned
to one of the supported 32 User Bands. The list of the User Bands’ parameters appears on the
next page. (ii) upon power-on, the Universal port functions as a standard universal port allowing
to connect a legacy receiver that is not supporting the Unicable/Unicable II (EN50494/EN50607)
protocols, however it switches to operate in a Unicable II mode as soon as it receives a EN50494
or EN50607 DiSEqC command and the 32 User Bands will be shared over the two output ports
(“shared User Bands” mode) and where each UB is only available at the output port through
which it was activated.
Note: The default configuration of the product, can be updated using Inverto’s Programmer de-
vice (not supplied with the product and sold as a separate accessory) and PC Windows software
that can be downloaded from www.inverto.tv.
Unicable II Programmable/cascadable
multiswitch with 32UB, 4 Universal/
Wideband Satellite inputs & 1 Terrestrial input
IDLU-UWT110-CUO1O-32P
Item: 5294
Satellite - Loop-through output
Terrestrial loop
through output
Terrestrial
input
M a d e i n C h i n a
D e s i g n e d i n L U
Satellite - Input
For default UB settings:
www.inverto.tv/dCSS-UB
V/L
V/H
H/L
H/H
U
niv
er
sal
Quattr
o LNB
(S
AT A/B/C/D)
2 x W
ideband LNBs
(S
AT A/B or C
/D)
DC in/
P
ower Inser
ter i
n
Horizontal
Vertical
110.50
113.50
Horizontal
Vertical
V/L
V/H
H/L
H/H
Satellite B or D
Horizontal
Vertical
Satellite A or C
Horizontal
Vertical
Satellite inputs:
- Universal Quattro LNB: 950 - 2150MHz
- 2x Wideband LNBs: 300 - 2350MHz
Terrestrial input: 47 - 862MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Default setup
Programmable setup
Satellite
A
C
Satellite
B
D
U
niver
sal Out
(+T
er
r)
(+T
er
r)
20.80
