background image

10

Safety

Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A light-
ning strike into the antenna may cause dangerous overvoltage over the product’s metallic/con-
ductive parts. 
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adap-
tor.If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long pe-
riods of time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the 
cable (wobbly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.

Troubleshooting

Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the 
satellite receivers are installed, connected and switched on according to available instructions. 
Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is 
the case, disconnect the product from the main power, and then find and remove the short cir-
cuit on the product inputs. Then re-connect the multiswitch to the main power. Frequent defects 
are in connector joints i.e. if the central conductor is too short and fails to make contact in the 
connector. Also the shielding braid should make proper contact with the connector coat. Some-
times a reset to the multiswitch microprocessor is sufficient to remove a fault: simply disconnect 
the multiswitch from main power for 30 seconds and then reconnect again. If you are unable to 
remove the fault yourself, please contact your distributor.

Disposal

Following relevant EU directives, this device shall not be disposed of together with municipal 
waste. Use local waste collection and recycling systems to dispose wore out products.

*DiSEqC™ is a registered trademark of Eutelsat

*For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be referred to  

  as detailed data-sheets of the products. Inverto Digital Labs reserves the right to amend, omit or add products,

  product-lines, and/ or features without notice.

Содержание Unicable II













Отзывы: