INVENTOR MGHP-12, Руководство пользователя

Страница: 9 / 72

7
OPERATING INSTRUCTIONS
Operating Instructions
- Press the "MODE" button until the "COOL" indicator
light comes on.
- Press the ADJUST buttons "+" or " - " to select your
desired room temperature. The temperature can be
set within a range of 17 C-30 C/62 F-88 F (or 86 F).
- Press the "FAN SPEED" button to choose the fan
speed.
O O O O O
- Press the "MODE" button until the "HEAT"
indicator light comes on.
- Press the ADJUST buttons "+" or " - " to
select your desired room temperature. The
temperature can be set within a range of
17 C-30 C/62 F-88 F (or 86 F).
- Press the "FAN SPEED" button to choose
the fan speed. For some models, the fan
speed can not be adjusted under HEAT
mode.
O O O O O
COOL operation
- Press the "MODE" button until the "FAN "
indicator light comes on.
- Press the "FAN SPEED" button to choose
the fan speed. The temperature cannot be
adjusted.
- Do not put the duct to window.
FAN operation
TIMER operation
HEAT operation
(cooling only models without)
AUTO operation
- When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating(cooling only models without), or
fan only operation depending on what
temperature you have selected and the
room temperature.
- The air conditioner will control room
temperature automatically round the
temperature point set by you.
- Under AUTO mode, you can not select the
fan speed.
FOLLOW ME/TEMP SENSING feature(optional)
To activate the Follow Me/Temp Sensing
feature, point the remote control towards
the unit and press the Follow Me/Temp
Sensing button. T
If the unit
does not receive the Follow Me/Temp Sensing
signal during any 7 minutes interval, the unit
will beep to indicate the Follow Me/Temp
Sensing mode has ended.
he remote display is actual
temperature at its location. The remote control
will send this signal to the air conditioner every
3 minutes interval until press the Follow
Me/Temp Sensing button again.
NOTE: This feature can be activated from the
remote control ONLY. The remote control
servesas a remote thermostat allowing for the
precise temperature control at its location.
- When the unit is on, press the
Timer button will initiate the Auto-off
stop program, the TIMER OFF
indicator light illuminates. Press the
UP or down button to select the desired
time. Press the TIMER button again
within 5 seconds, the Auto-on start
program is initiated. And the TIMER
ON indicator light illuminates. Press
the up or down button to select the
desired Auto-on start time.
Error codes and protection code:
E1-
E2-
E3-
E4-
P1-
Room temperature sensor error-
Unplug the unit and plug it back in.
If error repeats, call for service.
Evaporator temperature sensor error-
Unplug the unit and plug it back in.
If error repeats, call for service.
Condenser temperature sensor error-
Unplug the unit and plug it back in. If error
repeats, call for service (on some models).
error-
Unplug the unit and plug it back in.
If error repeats, call for service.
Bottom tray is full - Connect the drain
hose and drain the collected water away.
If protection repeats, call for service.
Display panel communication
POWER MANAGEMENT feature
- Press the "MODE" button until the "DRY"
indicator light comes on.
- Under this mode, you cannot select a fan
speed or adjust the temperature. The fan
motor operates at LOW speed.
- Keep windows and doors closed for the
best dehumidifying effect.
- Do not put the duct to window.
DRY operation
NOTE: Under AUTO mode, both the AUTO
mode and the actual operation mode
indicator lights illuminate. When the ambient temperature is lower (Cooling
mode) or higher (Heating mode) than the setting
temperature for a period of time, the unit will
be automatically operate power management
feature. T
he power management indicator light
When the ambient temperature is higher (Cooling
mode) or lower (Heating mode) than the setting
temperature, the unit will be automatically quit the
power management feature. The power
management indicator light
he compressor and fan motor stop and
t illuminates.
turns dark and the
compressor and (or) fan motor run.