A6
MODE 1 (28.8V/3.5A)
This mode is suitable for charging 24V batteries with capacity range from 14-120Ah in normal conditions. Connect the
output terminals of the charger to the battery with right polarity. Connect the power cord to the power outlet to begin
charging.
Press the selection button
⑭
to select Mode 1 (LED 2). After executing this operation the corresponding LED
display
②
will light up. If no further process is activated, the electronic system will automatically start the
charging with a current of 3.5A ±10%. Charging shall continue in several stages:
⑩→
⑪→ ⑫→ ⑬
until
battery is fully charged upto 28.8V±0.25V. At this stage all intermediate charging status LEDs display
⑩
,
⑪
,
⑫
will turn on one by one until, LED display
⑬
will turn on. The Trickle current is now available to battery for
maintenance.
MODE
MODE 2 (29.4V/3.5A)
This mode is suitable for charging 24V batteries with capacity range from 14-120Ah in cold conditions or charging several
AGM batteries. Connect the output terminals of the charger to the battery with right polarity. Connect the power cord to
the power outlet to begin charging.
Press the selection button
⑭
to select Mode 2 (LED 3). After executing this operation the corresponding LED display
③
will light up. If no further process is activated, the electronic system will automatically start the charging with a
current of 3.5A ±10%. Charging shall continue in several stages:
⑩→
⑪→ ⑫→ ⑬
until battery is fully
charged upto 29.4V±0.25V. At this stage all intermediate charging status LEDs display
⑩
,
⑪
,
⑫
will turn on
one by one, until LED display
⑬
will turn on. The Trickle current is now available to battery for maintenance.
MODE
MODE 3 (14.4V/7A)
This mode is suitable for charging 12V batteries with capacity range from 14-230Ah in normal conditions. Connect the
output terminals of the charger to the battery with right polarity. Connect the power cord to the power outlet to begin
charging.
Press the selection button
⑭
to select Mode 3 (LED 3). After executing this operation the corresponding LED
display
④
will light up. If no further process is activated, the electronic system will automatically start the charging
with a current of 7.0A ±10%. Charging shall continue in several stages:
⑩→
⑪→ ⑫→ ⑬
until battery is
fully charged upto 14.4V±0.25V. At this stage all intermediate charging status LEDs display
⑩
,
⑪
,
⑫
will turn
on one by one, until LED display
⑬
will turn on. The Trickle current is now available to battery for maintenance.
MODE
If you press
⑭
, charging mode automatically switches to the next operation mode and begins functioning in that
specific mode. However after a full charge, if battery is not disconnected from the charger, it remains in float charge
mode, even if user switches it over to another mode. This protects battery from being damaged.
MODE
Switching over between different Modes
By repeatedly pressing the selection button
⑭
displays the charging modes in the following order-
a) for 12V battery:
① →
“Mode 3” (14.4V/7A)
→
“Mode 4” (14.7V/7A)
→
“Mode 5”
( 13.6V/5.0A)
→
“Mode 6” (16V/1.5A) and repeats this cycle.
① →
“Mode 1” (28.8V/3.5A)
→
“Mode 2” (29.4V/3.5A) and repeats this cycle.
b) for 24V battery:
BOOST
MODE
Charging Status Indication
FLASH OFF OFF OFF Below 25% Diagnosis & Recovery
ON FLASH OFF OFF Below 50% Bulk
ON ON FLASH OFF Below 75% Bulk
ON ON ON FLASH Below 100% Absorption
ON ON ON ON Full Maintenance
Charging Status Charging Phases
⑩ ⑪ ⑫ ⑬
