Invacare TDX-SP N Скачать руководство пользователя | Manualshive

Страница: 2 / 88

background image

REFERENCE DOCUMENTS

2

Part No 1143209

DANGER

Risk of Death, Serious Injury or Damage
Improper use of this product may cause injury or damage.
If you are unable to understand the warnings, cautions or instructions, contact a health care

professional or dealer before attempting to use this equipment.
- DO NOT use this product or any available optional equipment without first completely reading and

understanding these instructions and any additional instructional material such as user manuals,

service manuals or instruction sheets supplied with this product or optional equipment.
Continued use of the wheelchair with damaged parts could lead to the wheelchair malfunctioning

causing injury to the user and/or caregiver.
- Check all wheelchair components and carton for damage and test components before use. In case

of damage or if the wheelchair is not working properly, contact a qualified technician or Invacare for

repair.

WARNING

Risk of Injury, Damage or Death
Improper setup, service, adjustment or programming may cause injury, damage or death.
– Qualified technician MUST setup, service and program the wheelchair.
– DO NOT allow non-qualified individuals to perform any work or adjustments on the wheelchair.
– DO NOT setup or service the wheelchair while occupied except for programming or unless

otherwise noted.
– Turn off power BEFORE adjusting or servicing the wheelchair. Note that some safety features will

be disabled.
– Ensure all hardware is securely tightened after setup, service or adjustments.
– Warranty is void if non-qualified individuals perform any work on this product.

DANGER

Risk of Death or Serious Injury
Not wearing your seat positioning strap could result in death or serious injury.
ALWAYS wear your seat positioning strap. Your seat positioning strap helps reduce the

possibility of a fall from the wheelchair. The seat positioning strap is a positioning belt only. It is

not designed for use as a safety device withstanding high stress loads such as auto or aircraft

safety belts. If signs of wear appear, seat positioning strap MUST be replaced IMMEDIATELY.

REFERENCE DOCUMENTS

Refer to the table below for part numbers of additional documents which are referenced in this manual.

MANUAL

PART NUMBER

MK6i™ Electronics Field Reference Guide

1141471

Adjustable ASBA user manual

1143196

Adjustable ASBA Service Manual

1143238

NOTE: Updated versions of this manual are available on www.invacare.com

«
1
2
3
4
...
»

Содержание TDX-SP N

























































































Отзывы:

Нет отзывов

Похожие инструкции для TDX-SP N

LOOK Transfer Bench 1475

Бренд: PARSONS ADL Страницы: 2

Бренд: Golden Technologies Страницы: 38

Бренд: Quickie Страницы: 36

Бренд: Quickie Страницы: 59

Бренд: Quickie Страницы: 78

Netti 4U comfort|CE

Бренд: Alu Rehab Страницы: 34

Atmos ultra CL200 38 Series

Бренд: ARDEA ONE Страницы: 60

Бренд: Pride Страницы: 55

Бренд: R82 Страницы: 119

Бренд: JDY Imports Страницы: 26

Бренд: Karma Страницы: 48

Бренд: Quickie Страницы: 29

Бренд: You-Q Страницы: 15

Бренд: Trekinetic Страницы: 54

Бренд: DeBug Страницы: 5

Бренд: BraunAbility Страницы: 9

Бренд: Golden Technologies Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды