Invacare Perfecto 2 IRC5P Скачать руководство пользователя страница 86

Страница: 86 / 88

SECTION 25—SIEVE BED PRESSURE CHECK

Perfecto

™

Part No 1148070

SECTION 25— SIEVE BED PRESSURE
CHECK

Checking Sieve Bed Pressure

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical outlet
before servicing.

Disassembly

NOTE: For this procedure, refer to FIGURE 25.1.

1. Turn power off ( ) and unplug unit.

2. Remove cabinet. Refer to Removing Cabinet on page 23.

3. Turn unit so the back faces you.

4. It may be necessary to remove compressor inlet HEPA filter. Refer to Replacing the

Compressor Inlet HEPA Filter on page 26.

FIGURE 25.1

Disassembly

Pressure Testing

NOTE: For this procedure, refer to FIGURE 25.2 on page 87.

1. Connect pressure gauge to the ¼ x 2-inch silicone tubing with connector (p/n 1131392).

2. Remove plug in HomeFill port in back of concentrator.

3. Connect ¼ x 2-inch silicone tubing with connector to HomeFill port.

Check Valve

Cut PVC Tubing below

Check Valve to install

Tap-in Kit

Product

Tank

Содержание Perfecto 2 IRC5P

























































































Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды

Invacare Perfecto 2 IRC5P, Руководство по обслуживанию

Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды