background image

Invacare® Modulite

5.5 Headrest/Neckrest

5.5.1 Replacing Rea Headrest

Removing Headrest

1.

Loosen hand screw

B

.

2.

Pull headrest

A

out of bracket

C

.

Fig. 5-2

Installing Headrest

1.

Install parts in reverse order.

2.

Tighten hand screw

B

hand-tight.

3.

Test all functions.

5.5.2 Replacing Rea Headrest Mounting Bracket (Sling Backrest)

4 mm Allen key

Removing Bracket

Not all bolts and washers are shown in illustration.

1.

Loosen and remove bolts

E

including washers

F

,

mounting plate

D

and bottom side of bracket

C

.

2.

Remove top side of bracket

B

including nuts

A

.

Fig. 5-3

Installing Bracket

1.

Install parts in reverse order.

2.

Test all functions.

5.5.3 Installing Elan Headrest to Flex3 Backrest

The Elan headrest can only be mounted to a Flex3 backrest via an adapter.

Risk of Damage to Property

After mounting parts of adapter, parts are difficult to separate again.

– Mount parts only within headrest housing.
– To dismount, use small Allen key or paperclip to disengage locking clips on inside while pulling parts apart.
– Mount parts completely to headrest mounting and ensure that parts engage with audible click.

Rubber mallet

Elan headrest adapter(s) for Modulite

22

1604311-G

Содержание AVIVA RX40













































Отзывы: