Invacare Action2 NG Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

background image

SECTION 4—SEAT/BACK

1 8

Removing/Installing/Adjusting the Back-Cane Bracket

NOTE: For this procedure, refer to FIGURE 4.8.

NOTE: To install the back-cane bracket, reverse this procedure.

4. Remove the back-canes. Refer to Removing Back-Canes paragraph.

5. Pull up on the seat upholstery.

6. Remove the two mounting screws and locknuts that secure the back-cane bracket to

the wheelchair frame.

7. Do one of the following:

•

To Remove:

the back-cane bracket by sliding it off the back of the wheelchair

frame.

•

To Adjust:

slide the back-cane bracket to one of the four adjustment holes on

the bracket.

NOTE: Both back-canes should be set to the same adjustment hole.

FIGURE 4.8

Removing/Installing/Adjusting the Back-Cane Bracket

Back-Cane

Bracket

Mounting

Screws

Locknuts

Adjustment

Holes

Back-Cane

Bracket

Mounting

Screws

Locknuts

Adjustment

Holes

«
...
16
17
18
19
20
...
»

Содержание Action2 NG

















































Отзывы:

Нет отзывов

Похожие инструкции для Action2 NG

Бренд: Q'STRAINT Страницы: 36

Бренд: HEALTH PRODUCTS Страницы: 11

Бренд: HOMECARE PRODUCTS Страницы: 6

Бренд: Probasics Страницы: 22

Бренд: Drive Страницы: 2

Бренд: Drive Страницы: 4

Бренд: Drive DeVilbiss Страницы: 24

Бренд: R82 Страницы: 12

Бренд: HD Страницы: 2

Jazzy Select 14 Series

Бренд: Pride Страницы: 2

Бренд: EZee Life Страницы: 2

Бренд: EZee Life Страницы: 23

Бренд: RMS Страницы: 14

Бренд: Observer Страницы: 51

Бренд: John Страницы: 20

Бренд: Karma Страницы: 116

Бренд: Paravan Страницы: 127

Бренд: Quickie Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды