background image

Page 5 / 6  

installation and user guide for the Intratone EEN-REC2   

V233-0011-AD receiver 

   

Rolling code operation 

 

The receiver manages the rolling codes emitted by the remote controls. They are intended to counter 
attempts  at  making  fraudulent  copies  of  remote  controls  (through  reproducing  the  signal  emitted  by 
the  remote  control).  Every  time  a  key  on  one  of  the  remote  controls  is  pressed,  a  code  is  emitted 
which  must  meet  criteria  known  only  to  the  EEN-REC2  receiver.  The  security  of  your  site  is  thus 
optimal. 
It  may  be  necessary  to  erase  the  rolling  codes  stored  on  the  receiver.  (The  installation  of  the 
receiver  on  another  site  for  example).  This  erasure  occurs  at  each  power  up  or  when  switching 
switch no.6 to the ON position (
Then switch no.6 back to the OFF position).  
 

Compliance with standards/ Limitations 

EC standards:  
The  RF  868Mh  EEN-REC2  receiver  complies  with  the  R&TTE  Directive  1999/5/EC:  electrical 
safety  standard  EN  60950(2000)  applied,  EMC  standard  EN  301  489-3  (2000)  applied,  radio 
standard
 EN 300 220-3 (2000) applied. 
 
Cabling:  
The  cables  used  to  connect  the  receiver  to  an  INTRATONE  RESIDENTIAL  central  unit  must  be 
installed in accordance with the instructions describing the level 2, protected environment, of the NF 
EN 61000-4-4 standard. 
Please follow the recommendations given in the cabling and connection diagrams, in particular with 
respect  to  the  distance  and  the  gauge  of  the  cables  between  the  RF  receiver  and  the  central  unit  or 
GSM unit. If this is not the case, no warranty will be given. 
 
End of life product recycling: 

The receiver and its accessories must not be disposed of with unsorted municipal waste, but 
must follow the WEEE (Waste Electrical and Electronic Equipment) collection and recycling 
channel.

 

 

Mounting 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

1)

 

Place the EEN-REC2 on the DIN RAIL or wall-mount it. 

2)

 

Set the switches. 

3)

 

Connect the coded aerial (with the optional aerial of required). 

4)

 

Connect the receiver to the central unit or GSM unit. 

 

 

DIN RAIL 

DIN RAIL 
fixing point 

Wall fixing point 

Intelligent Security & Fire Ltd.

Содержание EEN-REC2







Отзывы: