Intimus 16.99 SmartShred, Руководство по эксплуатации, Страница: 13 / 34

95663 3 03/22
GB
27
16.99 SmartShred
7 Malfunction
DANGER!
Risk of death by electrocution!
Always unplug the machine from the mains po-
wer supply, turn off the main switch and lock it
with a padlock before opening the machine to
carry out any repairs.
NOTE!
If operating errors occur, specific pop-up windows
containing error messages appear on the display.
These provide information about the cause and re-
medies.
If the problem cannot be resolved, touch the blue
question mark — the address of your service tech-
nician appears.
7 .1 Motor faults
If the shredder or baler should become overloaded, an in-
stalled thermostat breaks the electrical circuit for full ope-
ration. A pop-up window containing the respective error
message appears.
After cooling (approx. 30 min), the machine can be used
again at full capacity.
NOTE!
If the machine no longer operates at full capacity,
even though the overheated motor has been allo-
wed to cool down (pop-up window no longer clo-
ses), there is a defect in the machine. In this case,
please inform our customer service department.
7 .2 Fault checklist
If the machine is not functioning properly, you should check
the following:
• is the machine plugged into the mains power supply?
• is the connector plug from the baler plugged into the
outlet (fig. 1/4) at the shredder?
• has the safety switch activator (fig. 4/1) been inserted
into the safety switch at the baler?
• has the key switch (fig. 7/1) been activated?
• is the mains switch (fig. 7/2) turned on?
• is the emergency stop bar (fig. 6) in the forward positi-
on?
¾
Pull red bar at table forward.
• is there a paper jam in the machine?
¾
Follow the instructions for „Automatic response in
case of „overloading““, p. 22.
• are the inlet flap (fig. 1/5) and the discharge flap (fig. 1/1)
at the baler closed?
• is the cover flap (fig. 1/3) closed?
¾
See description under „16.99 with baler: Jam outlet“,
p. 22 .
• is the motor overloaded?
¾
Please refer to the section headed „Motor faults“,
p. 27 .
• is there a phase failure?
¾ Check the three-phase fuse at the power supply so-
cket, and replace if necessary.
NOTE!
If none of the listed inspection points are relevant,
or if other machine malfunctions are identified, the
machine must not be operated! In such cases, ple-
ase inform our customer service department.
8 Maintenance / Disposing
8 .1 Gear box maintainance
DANGER!
Risk of injury from electric shock and moving
parts!
Before opening the housing, switch off the ma-
chine at the main switch and unplug the mains
plug.
NOTE!
The machine may not be modified in any way!
Operation of the machine is prohibited if modifica-
tions are undertaken!
Both synchron gears, as well as the chain wheels and drive
chains must be greased monthly.
Proceed as follows:
1 .
Remove the right-hand side panel from the housing.
2 .
Grease the above mentioned parts with a brush or a gre-
ase gun, and a standard, commercially available grease.
3 .
Re-install the side cover and connect the machine to
the mains. The machine can be put back into operation.
8 .2 Energy saving tip
Be certain that the machine is turned off overnight (main
switch (fig. 7/2) switched to „0“).
8 .3 Checking the oil level
Unscrew the dipstick (fig. 26/1) in order to check the oil le-
vel. The marking on the dipstick must be wetted with oil. If
this is not the case, add oil.