background image

    SAVE THESE INSTRUCTIONS

Page 2

(249PO)  MODEL ECO7111  Cartridge Filter Pump & Saltwater System with E.C.O.   ENGLISH  7.5” X 10.3”  PANTONE 295U  04/06/2017

English

249

PO

S  AVE THESE INSTRUCTIONS

English

Page 27

TROUBLESHOOTING GUIDE (continued)

1

. Circulation line is blocked.

2

. Incorrect inlet and outlet hose direction.

3

. Scale on the flow sensor.

4

. Flow sensor cord is loose.

5

. Inner timer confliction between filter 

  pump and saltwater system.

6

. Flow sensor failure.

1

. Dirt or scale on titanium plates.

2

. Low salt level / No salt.

3

. Electrolytic cell cord is loose.

4

. Possible electrolytic cell failure.

1

. High salt level.

1

. Display and all lights are off - the 

  system does not power up.

•  If your unit has plunger valves, ensure that 
  they are open.
•  Clear your filter cartridge and cell from debris 
  and dirt. See “Maintenance”.
•  Release all trapped air in the circulation line. 
  See the filter pump manual.

•  Check the direction of the inlet and the outlet 
  hose. Reverse the hoses if necessary. See 
  “Set Up Instructions”.

•  Clean the flow sensor, paying special attention 
  to the hinge. See “Maintenance”.

•  Plug the flow sensor firmly into the flow sensor 
 receptacle.

•  Reset both timers on the filter pump and 
  saltwater system. See “Boost Cycle”.

•  Contact Intex Service Center.

•  Remove the electrolytic cell for inspection. 
  Clean it if necessary. See “Maintenance”.

•  Add salt. See “Salt & Pool Water Volumes”.

•  Ensure that the cell cord is plugged firmly into 
  the cell housing receptacle.

•  Contact Intex Service Center. Replace the cell 
 if 

needed.

•  Partially drain the pool and refill it with fresh 
  water. See “Salt & Pool Water Volumes”.

•  Household voltage is too high or too low 
  (+ 20%). Check the voltage is within the range 
  stated on the device housing.
•  Contact Intex Service Center.

LED PANEL 

CODE

PROBLEM

SOLUTION

 LED Panel Code Flash & Alarm On (

NOTE:

 Always turn off the power before cleaning and servicing).

IMPORTANT

If you continue to experience difficulty, please contact our Consumer Service Department for 
assistance. See separate “Authorized Service Centers” sheet.

Содержание ECO7111






























Отзывы: