Interroll SH 1100 Скачать руководство пользователя страница 59

Страница: 59 / 88

Interroll Module belt conveyor SH 1100

Maintenance and repair

Version 1.0 (06/2022) en
Translation of original operating instructions

Replacing rollers/axles

Overview of rollers/axles for module belt conveyor - straight with head drive

Drum motor

Front idler axle

Return axle

Overview of rollers/axles for module belt conveyor - straight with center drive

Front idler axle

Idler pulley

Return axle

Drum motor

The rollers and axles of the module belt conveyor may require the following maintenance tasks
to be performed or parts to be replaced:

• Replace the entire center drive station,

see "Replacing the center drive station", page 60

• Replace the drum motor (head drive),

see "Replacing the drum motor (head drive)", page 62

• Remove the holder from the drum motor,

see "Removing/installing holder from/on the drum

motor (head drive)", page 63

• Remove the drum motor (center drive),

see "Removing/installing drum motor (center drive)",

page 64

• Replace sprockets at drum motor,

see "Replace the sprockets", page 66

• Replace return axle,

see "Replacing the return axle", page 67

• Replace idler axle at the front,

see "Replacing the front idler axle", page 68

Содержание SH 1100

























































































Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды

Interroll SH 1100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды