*1280*
*1280*
Unsatisfactory Scan:
Cause of Problem:
Starting the scan within the bar code
or scanning too slowly.
Stopping within a scan or varying the
rate of velocity across the bar code.
Not staying in the bar code during the
entire scan.
Also, inspect the quality of the bar code labels that are being used. Low contrast,
scratched, or otherwise defaced bar code may cause scanning problems.
MAINTENANCE
Cleaning
For optimum performance, keep the wand clean and dry. Remove debris from the tip
with a soft cloth. The wand barrel and the end cap can be cleaned with isopropyl
alcohol or a mild detergent applied to a soft cloth. Do not allow moisture to enter the
wand. Do not immerse the wand in fluid.
TIP REPLACEMENT
The tip must be replaced if the scanning window is chipped, cracked, or scratched.
1. Remove the tip by inserting a thin coin into the tip locking ring and prying it off
the end of the wand.
Be careful not to damage the optical surface within the opening of the wand barrel.
2. Place the new tip in the end of the wand, being careful not to touch the exposed
optical surface.
3. Press the tip against a smooth, hard surface. Hold the wand firmly and press
downward until the tip snaps into place.
*SCAN*
*SCAN*
*SCAN*
➤
➤
➤
➤
➤
➤
➤
•
•
➤
Accessories:
Function:
Ordering No:
Edge Guide
Facilitates scanning bar codes on the edge of
048275
circuit boards.
Wand Holder
Provides storage for the wand when not in use.
061064 (blue)
046993 (brown)
047175 (gray)
Replacement Tip
062441
SCANNING PROBLEMS
The reader emits an audible tone when a bar code label is correctly scanned. If it does
not, check your scanning technique.
©1995 Intermec Corporation • All Rights Reserved • PN 062442-004 • 6001 36th Avenue West • P.O. Box 4280 • Everett, Washington 98203
*1280*
*1280*
Unsatisfactory Scan:
Cause of Problem:
Starting the scan within the bar code
or scanning too slowly.
Stopping within a scan or varying the
rate of velocity across the bar code.
Not staying in the bar code during the
entire scan.
Also, inspect the quality of the bar code labels that are being used. Low contrast,
scratched, or otherwise defaced bar code may cause scanning problems.
MAINTENANCE
Cleaning
For optimum performance, keep the wand clean and dry. Remove debris from the tip
with a soft cloth. The wand barrel and the end cap can be cleaned with isopropyl
alcohol or a mild detergent applied to a soft cloth. Do not allow moisture to enter the
wand. Do not immerse the wand in fluid.
TIP REPLACEMENT
The tip must be replaced if the scanning window is chipped, cracked, or scratched.
1. Remove the tip by inserting a thin coin into the tip locking ring and prying it off
the end of the wand.
Be careful not to damage the optical surface within the opening of the wand barrel.
2. Place the new tip in the end of the wand, being careful not to touch the exposed
optical surface.
3. Press the tip against a smooth, hard surface. Hold the wand firmly and press
downward until the tip snaps into place.
*SCAN*
*SCAN*
*SCAN*
➤
➤
➤
➤
➤
➤
➤
•
•
➤
Accessories:
Function:
Ordering No:
Edge Guide
Facilitates scanning bar codes on the edge of
048275
circuit boards.
Wand Holder
Provides storage for the wand when not in use.
061064 (blue)
046993 (brown)
047175 (gray)
Replacement Tip
062441
SCANNING PROBLEMS
The reader emits an audible tone when a bar code label is correctly scanned. If it does
not, check your scanning technique.
©1995 Intermec Corporation • All Rights Reserved • PN 062442-004 • 6001 36th Avenue West • P.O. Box 4280 • Everett, Washington 98203
This 1280 Series Wand complies with
the European EMC and Low Voltage
Directives. It has been tested to EN
55022, EN 50082-1, and EN 60950
This 1280 Series Wand complies with
the European EMC and Low Voltage
Directives. It has been tested to EN
55022, EN 50082-1, and EN 60950
ORDERING INFORMATION
Wands and accessories can be ordered by contacting your local Intermec Sales Office.
ORDERING INFORMATION
Wands and accessories can be ordered by contacting your local Intermec Sales Office.
