background image

Trouble Shooting

SYMPTOM

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

Time switch has no display.

Battery not properly installed or

Check battery and replace if necessary.

defective.

Display shows “L-bA”.

Display means “Low Battery”.

Replace battery within 30 days.

Display shows “Err 1” message. Slide switch not fully in its detent

Reposition slide switch into detent or “wiggle” until

position (open circuit).

display is corrected. If display does not correct,

Display shows “Err 2” message. Slide switch shorted circuit.

contact or return to factory for service.

Display shows “Err 3” message.  Slide switch illegal position.

Display shows scrambled or

Time switch has not been reset.

Press the recessed reset switch and hold for

erratic times.

approximately 5 seconds.

Electrical noise is interfering with the

Electrical noise interference is highly unlikely

operation of the microprocessor.

since the electronic circuitry and the power
supply are completely isolated. The installation
of surge suppressors (metal oxide varistors-
MOVS) across terminals 3/4 (model ET104C
across terminals 3/4 & 5/6) will help to reduce
electrical noise generated at the switching
contacts.

Load does not switch at-

MANUAL/AUTO selector not in AUTO

Be sure MANUAL /AUTO is in the AUTO

programmed time.

position.

position.

Time switch is programmed incorrectly/

Check program - place the Program Selector in
the PROGRAM mode and press the Event button
to review all eight possible Events.

Power has not been supplied to the

Be sure power is applied to the line terminals #3

load through the line (line 1 and

(#3 and #5 for ET104C) in order to power the

line 2 for ET104C) terminals.

load. Note that the output contacts are isolated
from the timer power (terminals 1 and 2).
This allows the timer to switch various loads
from 24 volts through 277 volts.

Unit overheats or unit

Voltage selector set incorrectly.

Be sure voltage selector on rear of timer

fails to switch load on.

matches timer supply voltage. See
item #2 under “installation.”

LIMITED ONE YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated
will repair or replace it, at its sole option, free of charge. This warranty is extended to the original household purchaser only and is
not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of
God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c)
units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs,
LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES
DO  NOT ALLOW  THE  EXCLUSION  OR  LIMITATION  OF  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES,  SO  THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED
WARRANTIES.  ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO
NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing
the product, along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by:
Intermatic  Incorporated/After  Sales  Service/7777  Winn  Rd.,  Spring  Grove,  Illinois  60081-9698/815-675-7000
http://www.intermatic.com   Please be sure to wrap the product securely to avoid shipping damage.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

158ET13247                                                                                                                                                                   

Содержание ET102CM

Страница 1: ...30 Amps Inductive Resistive 24 120 240 V A C 60 Hz 20 Amps Resistive 28 V D C 1 H P 120 V A C 60 Hz 2 H P 240 V A C 60 Hz 5 Amps Tungsten 120 240 V A C 60 Hz 20 Amps Ballast 277 V A C 60 Hz SET POINTS EVENTS 8 total 4 ON 4 OFF BATTERY POWERED CLOCK OPERATION 3 Years minimum AA industrial grade alkaline supplied with time switch MIN ON or OFF TIME 1 minute MAX ON or OFF TIME 23 hours 59 minutes SHI...

Страница 2: ...ting as marked on circuit board See Fig 2 CAUTION DO NOT TOUCH THE CIRCUIT BOARD COMPONENTS SINCE STATIC DISCHARGE COULD DAMAGE THE MICROPROCESSOR 3 Replace the mechanism in the case if it has been removed 4 Lift the left side of the insulator off of the retaining post and pivot it up and away to expose the terminal strip 5 Strip the supply and load wires by removing 1 2 inch of insulation DO NOT ...

Страница 3: ...ssed you can achieve a fast roll of the displayed time This is useful when setting the time of day or setting the programmed set points events Up to 4 ON and 4 OFF set points 8 events can be programmed The load can manually be switched ON or OFF at any time only if the selector switch is in the RUN mode by pressing the ON OFF button Pressing the ON OFF button two times in the PROGRAM mode causes t...

Страница 4: ...See item 2 under installation LIMITED ONE YEAR WARRANTY If within one 1 year from the date of purchase this product fails due to a defect in material or workmanship Intermatic Incorporated will repair or replace it at its sole option free of charge This warranty is extended to the original household purchaser only and is not transferable This warranty does not apply to a damage to units caused by ...

Отзывы: