P/N 146551999-1 • REV C • ISS 30APR12
7 / 48
Green mode
When SW1-5 is set to Remote on, the radar is switched off
during the day mode (with no WT) to reduce current
consumption. The detector is then operating in PIR only mode.
Note:
The Day/night line must be connected to the control
panel for this mode to work.
Alarm memory
When SW1-5 is set to Remote on, alarms that occurred during
the night mode are stored in the detector memory. They are
indicated by flashing red LED when the unit switches to day
mode (walk test disabled). The memory is cleared when the
detector switches back to the night mode.
Note:
Set SW1-6 to Off to prevent showing the alarm memory
on the LEDs. See “SW1-6: LEDs” on page 6.
LEDs and outputs
To enable LEDs functionality, set SW1-6 to On, otherwise
LEDs are disabled in any condition. See “SW1-6: LEDs” on
page 6 for more details.
Table 6: LEDs and outputs
Status Red
LED
Yellow
LED
Alarm
relay
Fault
relay
To reset
Start up
Closed Closed
Automatically
after 60 s
Low voltage
Open Open
Apply
correct
voltage
PIR intruder
alarm
Closed Closed
Microwave
intruder alarm
Closed Closed
Dual motion
intruder alarm
Open Closed
Automatically
after 3 s
Latched PIR
(memory)
Closed
Closed Switch to the
night mode
AM alarm
Depends
on SW2-4
Open Depends
on
SW2-3
Technical fault
Closed Open Successful
walk
test
Continuously on
Normal blinking (1 Hz)
Specifications
Detector technology
Dual+AM
Range
4, 6, 9, 12 m selectable via SW1-1
and SW1-2
Viewing angle
78 degrees
PIR optics
9 high-density mirror curtains
Microwave frequency
5.8 GHz
Max microwave output at 1 m
0.003
μ
W/cm²
Memory function
Yes
Input power
9 to 15 V
(12 V nominal)
Peak-to-peak ripple immunity
2 V (at 12 V
)
Detector start-up time
60 s
Current consumption
10 to 20 mA (10 mA nom.)
Mounting height
1.8 to 3.0 m (5.90 to 9.84 ft.)
Target speed range
0.2 to 3.0 m/s (8 in./s to 10 ft./s)
Alarm (NC) / Tamper relay
characteristic
80 mA 30 V
, Form A
Fault relay characteristic
80 mA 30 V
, Form A
Alarm time
3 s
Operating temperature
−
10 to +55°C (14 to 130°F)
Relative humidity
95% max., noncondensing
Weight 120
g
Dimensions (H x W x D)
126 × 63 × 50 mm
IP/IK rating
IP30 IK04
Pry-off tamper
Yes
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information
www.utcfireandsecurity.com or www.interlogix.com.
For customer suppDA: Installationsvejledning
Beskrivelse
DD1012AM(-D) er en kombi detektor med antimask (AM).
Den omfatter den patentbeskyttede PIR-spejloptikteknologi
med den patentbeskyttede Range Controlled Radar-teknologi.
Installationsvejledning
Se figur 1.
Detektoren er beregnet til vægophæng men kan også
monteres i loftet med et monteringsbeslag.
Følg denne vejledning til at fastlægge den bedste placering til
installation af detektoren.
•
Monter detektoren så den forventede bevægelse ved et
indbrud er på tværs af detektionsmønstret (se figur 3).
•
Monter detektoren på en stabil overflade i en højde på
1,8 m — 3,0 m fra gulvet.
•
Monter ikke detektoren på en afstand af 0,5 m fra
metalgenstande eller 1,5 m fra lysstofarmaturer.
