Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 376

background image

Chapter 5: Menu reference

226

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

7.1.n.3 Special day

1>Day type
Normal Day

Enter the menu to configure the selected day as a special day.
For more information, see Chapter 3 “System functions > Special days in

schedules” on page 78.

7.1.n.3.1 Day type

1 Day type
>Normal day<

Choose a type for the selected day:
• Normal day: A normal day. A special day time frame is not valid.
• Holiday, Special day 2 etc.: The day is one of special days defined in “7.2.n.6

Special days” on page 230.

7.1.n.3.2 Recurring

2 Recurring
>Yes<

If set to Yes, the special day repeats every year. Otherwise, it is valid only once

on the defined date.

7.1.n.3.3 Until date

3 Until date
>10.03.2016<

If the end date is set, the special day object will cover a time period from the

selected day to the end date set in the Until date menu.

Note:

A time period overwrites other special days in case of overlapping.

7.2 Schedules

0>Add Schedule
1 Schedule 1

Each panel action performed automatically can be driven by up to two schedules.

Use the Schedules menu to add and modify schedules.
The maximum schedule number in the system is given in “General features” on

page 36.
For more information on schedules see “Schedules” on page 77 in Chapter 3

“System functions”.

«
...
230
231
232
233
234
...
»

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS1500A-IP-LP

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Calpeda Страницы: 4

Бренд: Eaton Страницы: 288

Бренд: Galaxy Control Systems Страницы: 5

Бренд: Magellan Страницы: 2

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Watts Страницы: 24

Бренд: Abocom Страницы: 10

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Dejero Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды