Interflex IF-80 Series Скачать руководство пользователя

Страница: 13 / 13

Interflex Datensysteme GmbH

13/13

8 Technical Specifications

Technical Specifications

Power Supply

12 - 24 V AC /DC

Power consumption

Max. 4 VA

Protection

Via PTC resistor

Interfaces

RS485, 9600/19200 baud (automatic recognition)

Reader

MIFARE or LEGIC Advant, depending on the order.

Sensor inputs

2 Floating sensors

Outputs

1 relay with floating NO/NC contact. Max. switching capacity 30 V, 2 A

User information

Buzzer; green/red LEDs and, depending on the display color, blue or white

General Data

Ambient temperature

-25°C to +55°C

Humidity

Max. 95%, non-condensing

Product safety

EN 60950-1

Compatibility (EMC)

ETS 300330-1/-2, EN 301489-1/-3, CE

Protection category

III

Degree of protection

IP54, provided that the cables are installed according to instructions.

Dimensions (L x W x D)

130.5 x 87 x 24 mm

Weight

0.32 kg

9 Disposal

Once its service life comes to an end, the device must be disposed of properly as

electronic waste. The owner can dispose of the device himself or return it to the

supplier.

Version Date: October 31, 2016

Interflex Datensysteme GmbH

Zettachring 16, D-70567 Stuttgart, Germany

Tel.: +49 (0711) 1322 0

Internet E-Mail: [email protected]

Websites:

www.interflex.de www.allegion.com

Содержание IF-80 Series














Результаты поиска

Содержание IF-80 Series

Отзывы:

Похожие инструкции для IF-80 Series

Бренды по названию

Популярные бренды

Interflex IF-80 Series, Руководство пользователя

Результаты поиска

Содержание IF-80 Series

Отзывы:

Похожие инструкции для IF-80 Series

Бренды по названию

Популярные бренды