Interfacion QED-PL2 Скачать руководство пользователя

Страница: 10 / 35

CONTROL COMMANDS

TURN THE DETECTOR ON

Ensure the battery power lead is connected to the lead socket on
the control box

PRESS the

once to turn the detector on.

Click on

this YouTube link

to see how to turn the QED on.

Note: The detector serial Number appears on the screen for a fraction of

a second after switch on

CYCLE THROUGH MAIN
MENU OPTIONS

PRESS either the

Button or the

button to toggle through the

Main Menu options (1-9)

TOGGLE BETWEEN A MENU
ITEM NUMBER OR ADJUST
VARIABLE

Pressing the

button toggles between displaying the menu

item number or a variable adjustment.

Note:

•

A single digit is the menu item number

•

Three digits indicates variable adjust mode

Click on

this YouTube link

to view an explanation of the QED

Control Panel functions.

INCREASE OR DECREASE A
VARIABLE

(e.g. GRD BAL)

Press the

button to increase a variable number

Press the

button to decrease a variable number

TURN THE DETECTOR OFF

PRESS and HOLD the

button for three seconds

Click on

this YouTube link

to see how to turn the QED off.

FACTORY RESET

Note: The factory reset can only be performed with the detector switched

OFF

PRESS and HOLD the

button, then press the

button for 2

seconds, then release the

button.

Click on

this YouTube link

to see how to perform a Factory reset

Tip:

Before doing a Factory Default
Reset (FDR) set the MGB to
anything but 100 before the
detector is turned off.

Once the detector has been
reset, if MGB is 100 then the
FDR has been done correctly.

Tip:

To quickly

get back to the MGB

adjustment screen from any
setting, push the AGB button
momentarily.

Содержание QED-PL2




































Результаты поиска

Содержание QED-PL2

Отзывы:

Похожие инструкции для QED-PL2

Бренды по названию

Популярные бренды

Interfacion QED-PL2, Руководство пользователя

Результаты поиска

Содержание QED-PL2

Отзывы:

Похожие инструкции для QED-PL2

Бренды по названию

Популярные бренды