manualshive.com logo in svg

Interactive Technologies Commander 2000, Руководство пользователя

Поделиться
Скачать
Interactive Technologies Commander 2000 Скачать руководство пользователя страница 46

46

Magic Key

Temporary Access Magic Key 
does not disarm system.

Use has expired. Reprogram Magic Key.

Lights

Light using X-10 Lamp Module 
doesn’t work.

Check light bulbs.
Check that light switch on lamp is turned ON.
Make sure lamp is plugged into an X-10 Lamp Module.
Make sure the lamp is plugged into a nonswitched outlet.
If light control still doesn’t work, contact your security 
consultant.

Panel

All panel lights blink.
Trouble beeps sound.

All panel lights are on steady.
Trouble beeps sound.

The system is in programming mode.
Contact your security consultant.

The system’s memory is clear. Contact your security con-
sultant.

Power

Panel announces, 

AC Power 

Failure.

Check to see if AC transformer is plugged into an outlet. 
If it is, check circuit breaker or fuse that controls that out-
let. If there is still an AC power failure, contact your 
security consultant.

Sensor

Panel announces, 

Sensor 

[sensor #] Trouble.

Panel announces, 

Sensor 

[sensor #] Failure.

Panel announces, 

Sensor 

[sensor #] low battery

.

Put the sensor’s cover on, if it is off. Activate the sensor.

The sensor is not communicating with the panel. Contact 
your security consultant.

See “Replacing Smoke Sensor Batteries” on page 44 for 
the procedure to replace your own smoke sensor batter-
ies, or contact your security consultant to have other sen-
sor batteries replaced.

Table 10

. Troubleshooting Your System

Problem

Solution

Technical Manuals Online! - http://www.tech-man.com

Содержание Commander 2000






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды