background image

1.800.737.5386  •  www.Inter-Fab.com 

11 

Troubleshooting

 

 

Problem: 

Cause: 

Solution: 

1.  Lift will not operate at all: 

Low Battery (Lift) 

– Red or 

amber LED on the receiver 
 
Damaged Battery (Lift) 

– Red 

LED on the receiver 
 
Dead Battery (Transmitter) 
 
 
Remote Locked 
 
 
Battery Fuse blown 
 

Recharge Battery 
 
 
Replace Battery* 
 
 
Replace Battery 
3V Lithium 2032 
 
Push unlock button for 
2 seconds 
 
Replace Battery Fuse 

2. The seat will not raise or lower. 
The seat will not rotate. 

Low battery (Amber LED on 
Receiver) 
 
Battery not installed properly 
 
Receiver malfunction 

Recharge battery 
 
 
Reinstall battery 
 
Replace Receiver* 
 

3. The seat’s motion isn’t smooth or sticks at a 
certain point during travel. 

Excessive wear to bearings 
 
Excessive wear to Actuator 

Replace bearings* 
 
Replace Actuator* 

4. The seat travels much slower than normal. 

Low battery 
 
Defective or worn-out battery 

Recharge battery 
 
Replace battery* 

5. The  lift  makes much more  noise  or  unusual 
noises during operation. 

Excessive wear to bearings 
 
Pivot points galling  

Replace bearings* 
 
Oil  pivots  with  light  oil 
(3-1) 

6.  Battery will not charge: 

Charger Fuse Blown 
 
Bad Battery (red LED on 
charger 

– not turning orange 

or green in 4 hours or less) 
 

Replace Charger Fuse 
 
Replace Battery* 

 
 

*  Please contact your local distributor or Inter-Fab Customer Service to order parts 1-800-737-5386 x121 

 
 
 
 
 

 
 

Содержание Portable i-Lift












Отзывы: