background image

Owner’s & Installation manual 

With air release valve, the other side is water inlet pipe. 
 
When  connect  water  collecter,  set  the  tightening  torque  to 
6180~7540N.cm(630~770kgf.cm),  and  use  a  spanner  to 
tighten it as shown in Figure.  
 
The  diameter  of  connective  junction  in  water  inlet  pipe  and 
water outlet pipe is RC3/4 tapper pipe thread inside. 
 
The diameter of condensate pipe is ZG3/4 tapper pipe thread  
outside.       

8.    PIPES CONNECTION 

Fig.8-1 

9.    INSTALLATING DRAINAGE PIPE 

Install the drain pipe of the fan coil unit 

Before out from factory, the scupper adopts the pipe thread.   

Be  sure  to  perform  heat  insulation  for  the  drain  pipe  of  the 
indoor unit. Otherwise, condensate will occur. The joint of the 
indoor unit should also undergo heat insulation treatment.  
 
When  performing  the  pipes  connection,  use  the  rigid  PVC 
binder, and make sure that no leak exists.  
 
Same  as  the  joint  of  the  indoor  unit.  Be  careful  not  to  apply 
force at the pipe side of the indoor unit.  
 
The  downward  gradient  of  the  drain  pipe  should  be  higher 
than (1/100), without bend in the middle.  
 
The  total  length  of  the  drain  pipe  when  pulled  out  traversely 
shall  not  exceed  20m,  when  the  pipe  is  over  long,  a  prop 
stand must be installed prevent winging.  
 

NOTE 

Fig.9-1 

Heat insulation  
      materials 

1.5m~2m 

Downward gradient  

is over 1/100 

The centralized pipes should be distributed against the figure 
shown on the right side.  

Drain test 
 

Before the test, ensure that the drain pipes are smooth and 
the adapters are sealed.  
 
Newly built rooms should undergo the drain test before the 
ceiling is laid.         

Fig.9-3 

Fig.9-2 

Bend 

S-shape  

As large as practicable (approx. 10cm) 

Downward gradient  

is over 1/100 

Содержание IFCH412KF-3









Отзывы: