background image

 

 

5

 

 

IT-7304-PC bottom coded switch

 

   

 

Bottom Coded Switch 

 

After time slot 0 is valid, other coded switches in whatever positions are all valid. 
Select the number of time slots according to the expected rate. Normally for an independent 
type, a time slot setting of automatic tracking Central Site module is selected. Coded switches 
of plate-clip time slot correspond to S1, S2, S3 and S4.   

 
 
 
 

   

Rear Panel of    IT-7304-PC/DC 

 

48V DC

  DC -48V power supply connector 

The others are the same as AC Rear Panel 
 

4.3 Front/Rear panels of Rack-mountable casing: 

 

RACK front panel

   

 

 

     

 

 

Front Panel of RACK 

+5V: 5V main power supply indicator lamp   

+12V: 12V fan power supply indicator lamp   
Under the panel is a group of indicator lamps matrix:   
PWR: power supply lamp 
RXD: lightening upon data receiving at V.35 
TXD: lightening upon data sending from V.35 
LOS: lightening when the optic line gets lost   
LOF: lightening after a synchronization of data out-of-frame 
TEST: lightening during loopback test (equivalent to LOOP)   
PTOK: lightening after a successful pseudo-random code test 

Содержание IT-7304-PC













Отзывы: