Intellihot iN199 Скачать руководство пользователя страница 26

Страница: 26 / 78

iN199 Air Intake Inlet and Exhaust Gas Outlet Pipe Connections 22
November 2021 - Revision 00

7.3.4 Roof Air Intake Inlet and Exhaust Gas Outlet

Pipe Termination

With this installation method, the terminations must extend

at least 12 inches over maximum potential snow levels, or as

required by local building codes. In areas of high snow fall,

protect the vent terminations from blockage.

Terminate the air intake inlet pipe with a 90° elbow (angled

down). A suitable roof flashing and vent cap (not supplied)

should be installed.

12" USA or

18" Canada

over maximum

snow level or

as required by

local code

12" Minimum

3' Minimum

12" USA or

18" Canada

over maximum

snow level or as

required by local

code

Exhaust

Intake Air

Single unit.

Intake Air

Exhaust

See

Note

Multiple units.

Note:

The distance between any exhaust gas outlet and air

intake inlet pipe should be between 18 and 36 inches

apart. If this minimum specification cannot be met,

the air intake inlet and exhaust gas outlet pipes should

be 72 inches apart or more.

7.4 Single Pipe Venting System

7.4.1 Single Unit

The following illustrations represent some typical venting

configurations and are included to assist in designing the

vent system. Possible configurations are not limited to these

designs.

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Exhaust

Содержание iN199















































































Результаты поиска

Содержание iN199

Отзывы:

Бренды по названию

Популярные бренды

Intellihot iN199, Руководство по установке и эксплуатации

Результаты поиска

Содержание iN199

Отзывы:

Бренды по названию

Популярные бренды