Intelligent Energy FCM-802 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

19

Number 10009655. A1

Fault

Cause

Action

No power from the
module

No command to start

Verify that the module is in Enable and Run modes
(see section 6 Connections)

Hydrogen leak

See 12.2

Check for fuel leak

Incorrect hydrogen pressure

See 12.3

Fuel check procedure

No power provided

See 12.4

Electrical system check procedure

Fuel cell is over temperature

See 12.5

Stack temperature check procedure

Maintenance procedures

11

11.1

11.2

12.1

User maintenance

The user can perform the following maintenance on the FCM-802/804:

· Monthly filter inspection
· Filter change
· Troubleshooting (see below)

Not performing these basic checks will reduce unit efficiency. For all other
maintenance tasks, contact Intelligent Energy Ltd.

Contact Intelligent Energy Product Support Team

In the event of a fault with the FCM-802/804, please contact the Intelligent Energy
Product Support Team. Either contact your local representative or email:

[email protected]

Please have the part number of your product and the serial number (on the
name plate). The part numbers are:

802: 10004360

804: 10004361

Trouble-shooting guide

12

Possible causes of faults

«
...
17
18
19
20
21
...
»

Содержание FCM-802





























Отзывы:

Нет отзывов

Похожие инструкции для FCM-802

Бренд: Magnavox Страницы: 2

Бренд: NANO Страницы: 28

Бренд: Bush Страницы: 36

Бренд: BNC Страницы: 14

Бренд: Simoco Страницы: 50

Бренд: Winco Страницы: 24

Бренд: Hantek Страницы: 37

Бренд: Sangean Страницы: 10

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 5

Бренд: Sangean Страницы: 1

Бренд: Sangean Страницы: 12

Бренд: Docktor Who Страницы: 8

Powermate Ultra PM0421100 Insert

Бренд: Coleman Страницы: 8

Powermate PM0525312

Бренд: Coleman Страницы: 8

Powermate PM0543002

Бренд: Coleman Страницы: 12

Бренд: Sunstech Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды